Menu
What's new
By:
Filters
Better Search

Recent content by nunu

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

  1. N

    WANFailover Dual WAN Failover ***v2 Release***

    hum ... so, what the conclusion ? it is a asuswrt firmware issue ? regards
  2. N

    WANFailover Dual WAN Failover ***v2 Release***

    hello, i try to follow script execution but it is a huge script :) i would like to know if the script is supposed to support starting in degraded condition ? (WAN0 Connected with loss at 100% & WAN 1 OK) regards
  3. N

    dual-wan router choice

    @Tech9 yes, it is more reliable but you can't have several openvpn instance (clients & server). rate performance is low (30Mbits/s) with openvpn as there is no hardware accelerator.
  4. N

    dual-wan router choice

    @glens it seems that we can't run openvpn client & serveur in same time, nor openvpn & wireguard in same time. in fact i would like to have: - multi wan - multi vpn instance (openvpn/wireguard), client & server in same time - possibility to select prefered output wan for vpn instances etc...
  5. N

    dual-wan router choice

    hi, RT2600ac crashes due to the flash issue... openvpn performances are bad ( 30 Mbit) as the cpu has no hw accelerator (AES-NI). Only one openvpn instance etc... RT-AC86U has better performance but synology rt2600ac functionnalities are reliable.
  6. N

    dual-wan router choice

    Thanks @Tech9 and @glens for your answers. For the moment with fail-over script it is not so bad with RT-AC2900. (I have identified an other issue in a specific case). Do you know which kind of issues was met on RT-AC2900 ? (2/3 most big issues?) regards
  7. N

    WANFailover Dual WAN Failover ***v2 Release***

    hello ! i made some tests. set up: - dual wan / load balancing - WAN0: box 4G - WAN1: box ADSL initial state: - WAN0 connected / no internet access - WAN1 connected / internet access OK I have notice that if the rooter reboot with WAN0 connected and no internet access : - i do not have...
  8. N

    WANFailover Dual WAN Failover ***v2 Release***

    ok, thanks for your answer. This could made some confusion (connected but no internet access) today 4G provider was down in the morning, and the router seems not have made things correctly as i hadn't access to internet though my adsl box. Unfortunately i haven't traces because i had to make it...
  9. N

    dual-wan router choice

    hello everybody ! i'm looking for a router with a fine support of dual wan. i had a synology rt2600ac (flash issue, poor ovpn performance, but good dual wan management). i have bought a asus RT-2900ac but dual wan management is not reliable (even with wan-failover script that improves a lot...
  10. N

    WANFailover Dual WAN Failover ***v2 Release***

    hi, logs in the post here regards
  11. N

    WANFailover Dual WAN Failover ***v2 Release***

    i think there is a misunderstood. the 100% loss is normal as i have unplugged the sim card of my 4G router. my "issue" is that, on 100% loss the WAN status of the wan0 is still displayed as connected (in wan-failover status) I would like to know if the status connected is an HW status (i mean...
  12. N

    WANFailover Dual WAN Failover ***v2 Release***

    maybe i was confused by wan-event script. Which are the caller of this script ? i have check in wan-failover script => it does not call wan-event ... in fact, i thought that wan-event script was called on an event on the WAN .. but a ping timeout is not that kind of event ... a cable...
  13. N

    WANFailover Dual WAN Failover ***v2 Release***

    hi, sorry ... my english can be confused :) ips are valid: 192.168.3.2 for WAN0 192.168.3.1 for 4G router connected to WAN0 WAN0 Target: 8.8.8.8
  14. N

    WANFailover Dual WAN Failover ***v2 Release***

    this is call at router boot. but if you check my traces (attached in a previous message), on wan-failover DISCONNECT state, there is (maybe 2 issues): - WAN status is displayed as connected - wan-event script not called.... Failure scenario starting here :
  15. N

    WANFailover Dual WAN Failover ***v2 Release***

    wan-event script permissions: -rwxrwxr-x in this case, i have added addition logs when wan-event sript is called: May 5 07:05:16 custom_script: Running /jffs/scripts/wan-event (args: 0 init) May 5 07:05:17 nunu: MANU WAN-EVENT CALL - 0 init May 5 07:05:17 custom_script: Running...
See more
Top