Menu
What's new
By:
Filters Better Search

Search results

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

  1. D

    Turning mains power on/off - will it damage my router?

    I have my router (AX86) and several other devices connected to a powerstrip with a on/off switch built in. Is it damaging for the electronics to turn the power off to a router (or other electronic devices) without using the on/off button on the router itself? Does it affect the longevity of a...
  2. D

    AX86U connection to AX58 Media Bridge - link rate gradually slows down.

    I have an AX86U as my main router and i am using a AX58U in Media Bridge mode (connected to my sons PC). After a "fresh" reboot of the media bridge and then main router (in that order) i get Tx/Rx link rates at around 3600Mbbps/2400Mbps (see attached picture, bottom row). After a day or two the...
  3. D

    Solved Unknown device associating and disassociating repeatedly

    Yesterday i rebooted my AX86U, and reset the log. This moning when i looked at the log i saw a lot of Association/Disassociation events like the ones below (i have replaced the MAC ADRESS) Jul 5 07:57:29 wlceventd: wlceventd_proc_event(527): eth7: Auth (MAC ADRESS), status: Successful (0)...
  4. D

    PC loses internet - help needed for troubleshooting

    Over the last couple of weeks my PC has started losing connection to the internet/drops connection. This has happened 4-5 times now, seemingly at random. The problem started about at the same time as i updated my router to asuswrt 386.42095 (now updated to 3.0.0.4.386.42840) but it could be...
  5. D

    5GHz band set to 160MHz bandwidth but shows as 80MHz on WiFi analyzer.

    I have put a checkmark in the "Activate 160MHz" on my AX86U (running Merlin 386.2 beta1) but when i check the WiFi with WiFi analyzer on my phone it says that it's only 80MHz. I have it on channel 44 at the moment, but channel 36, 64 and 100 all give the same results. Everything is set up as...
  6. D

    AX86U - Cabled device keeps dissapearing and reappearing in list of clients

    I recently bought two AX58U router to use in a AiMesh setup. This wekend i found a good deal on a AX86U and i bought it after reading a lot of positive mentions about it here in the forum. I had hoped that the AX86U would cover my apartment better to avoid having two routers in AiMesh (problem...
  7. D

    My AX58U won't broadcast 5GHz WiFi on channels 116-128.

    This morning i changed the 5GHz channel from 100 to 116 (less interference according to my WiFi analyzer app) on my 40 days old AX58U. However, once i set it and applied i had no 5GHz WiFi - it couldn't be seen by either my phone or my other WiFi devices. I tested all channels from 100-140: When...
  8. D

    New to AiMesh. Firmware update - advice on procedure needed.

    I recently bought two AX58U routers that i use in an AiMesh. So far i only use stock firmware. New firmware came out yesterday and i would like to update the firmware on both node and router. In which order should i update the router and node? From what i have read here on the forum it is...
  9. D

    AiMesh questions from a newbie

    Greetings all :) I have been reading through this great forum for a while and this is my first post here. I don't have that much experience with networking and very limited knowledge, but i am willing to learn as much as i can. Backstory: I have recently receieved a new modem/WiFi router from...
Top