Advanced search results
Better search
Select: Thread titles
Keywords: aimesh
Posted by:
Search forums: Selected
Results count: 327
Select: Thread titles
Keywords: aimesh
Posted by:
Search forums: Selected
Results count: 327
-
- 6 Posts - toaruScarI have installed ZenWiFi XT8s on Merlin firmware. The AiMesh pages indicate that the wireless backhaul has a PHY rate of 1441 Mbps. However, when I run iperf3 between these two routers, it achieves only 350 Mbps. On the wireless log page, the utilization jumps to 80% during the iperf3 session... -
D- 1 Posts - darkchengHas any one got 2 GT-AX11000 Pro Using one as a Aimesh node through the 10g Port? unless the default, in AiMesh node, is only the Primary 1G/2.5G WAN port? the Rapture WebUI doesn't provide much option to validate I'm about to get a second one, in order to connect the other end of the house...
-
S- 3 Posts - sisimonHello. I previously had a tp-link mesh network Deco M4 (5 pieces). However, there was a problem with wifi calling with Samsung phones. It was very good with other phones. I have now bought Asus RT-AX82U and node RT-AX59U. I have a good range in 5GHz. However, I would like to buy a router to...
-
- 3 Posts - elrengoHi! I have both routers and I want to set up my second router, the RT-AC66U B1, as an AiMesh node. The RT-AX88U Pro found it and started setting up. The process has been interrupted and therefore has not been completed, leaving the router RT-AC66U B1 unable to finish the boot-up process. The... -
R- 3 Posts - reliably139Hi everyone, I got a problem I think it can not be solved. I tried to find some advanced device and finally bough Asus RP-AX58 but I think I can not do what I need. I have a mesh at home with main router and one node connected by ethernet and with backhaul enabled. I need or I think I need to...
-
- 29 Posts - DianaReaHello, This is my first post here. I had a ASUS GT-AX6000 wifi router for a few years which worked excellent. I recently moved to a new place in which the single access point cannot cover the premises. So I figured that I needed one more ASUS GT-AX6000 to extend the wifi coverage and that... -
R- 13 Posts - Rpadilla65This is my setup, I have a GT-AXE-16000, two RT-AX92U, three Lyras and I recently purchase a GT-AX6000. The AXE-16000 has the beta firmware and I enable an IoT and guest networks. After enabling it, the two RT-AX92U started individual, open, guest networks, when they connect as most of the time...
-
B- 2 Posts - barkmarkinHey guys, I've been happily using my AX88U Pro as main router, however I have a spare RP-AX58 extender and a RT-AX58U router, and I moved to a larger house but only need to use one of them, I wish I could throw another AX88U Pro in but Which would be the better option? Of course it's going to...
-
L- 7 Posts - lucaasHi everyone, I have a pair of XT8s running on firmware 3.0.0.4.388_24621 in AiMesh mode. To connect some wired devices, I bought a RT-AXE7800 (firmware 3.0.0.4.388_25058) and tried to use it as the main router and the XT8s will be nodes. The backhaul is wireless. The router configuration for...
-
S- 3 Posts - SDooI found a lot of information on SNB, it was very helpful. But still a small thing I didn't found... I can enable a Guest network on the AiMesh router by using CLI - telnet: nvram set wl0.1_bss_enabled=1 But then it is only enabled on the router, not on the nodes. When using the web or app, it...
-
B- 8 Posts - bofh99Hi, I can't get aimesh to work on RT-AX58U V2 with two ac68u clients. It 'sees' the clients but is unable to pair up with it. It gets slowly to 40% progress then speeds up then says it's unable to pair up, with the following error: Unable to add your AiMesh node RT-AC68U...
-
E- 6 Posts - erick_eMy primary router is a GT-AXE16000 using 2.4GHz, 40MHz, Channel 11; 5GHz-1, 80MHz, Channel 40; 5GHz-2, 160MHz, channel 112; and 6GHz, 160MHz, channel 37. I live in a two story house, approx. 1500 sq/ft, and the router is perfectly sufficient for anything we do on the second floor living apace...
-
- 6 Posts - BlueOrbitWhy is the icon on my "Second Floor" AI Mesh node incorrect? No big deal, but just wondering if anyone has experienced this also? -
- 9 Posts - SupermaticoHello, for my AiMesh master I already done Is there a way to give a static IP also to the node (RT-AX88U)? Note that my node is in Backhaul connection (wired) In LAN/DHCP Server/Manually Assigned IP around the DHCP list there all the peripherals, not the node Sorry, I did a forum search... -
W- 5 Posts - welimDear All, My AIMESH router is AX86U-PRO and my AIMESH node is AX11000. Recently after the merlin firmware update to the 388.8.0 , I found something weird. My authentication method is setup to be both http/https (Administration->System->Authentication Method -> BOTH) 1. When I click upload...
-
D- 7 Posts - DougjI am currently running a AiMesh network with an RT-AX88U as the primary router and a RT-AX58U as a node and it works great except that I can no longer update the firmware of either as the update fails. I did however find a fix for that https://www.asus.com/support/faq/1030652/ and will run...
-
- 3 Posts - Rana ImranHi. I recently started using the ASUS RT-AX82U router with Firmware Version: 3.0.0.4.388_24963. I've set it up in an AiMesh system configuration with the following devices: ASUS RT-AX82U (AiMesh Router) ASUS RT-AX82U (AiMesh Node) DSL-AC68U (AiMesh Node) The issue I'm encountering is with the... -
M- 5 Posts - mower8739Title is basically it. I have an XT12 in the central area of my apartment. 2.4GHz set up for my IoT, cell phones and Google Home speakers connect to 5GHz-1, and 5GHz-2 set up specifically for PCVR and VR headsets. I purchased an ET12 and positioned it in my Office. Ethernet backhaul enabled...
-
T- 2 Posts - tlxxxsracerPicked up an open box Gt-axe11000 off Amazon. After setting it up I noticed one antenna sticking further away from the housing than the others. First pic is the antenna and example of the others. I try pushing it in (what I felt should've been a comfortable force). Anyone have recommendations...
-
- 7 Posts - SupermaticoHello to all, I have an ASUS RT-AX88U PRO as a main router and an RT-AX88U as a AiMesh node, both with Merlin firmware, 388_7 Now, before to update both to the latest 388_8 firmware version I need to know if there is a correct procedure to follow to don't become crazy to set everything back...
-
N- 9 Posts - NewtonFruttHi folks, I'm new to all this coming from Ubiquiti but very impressed so far. I'm having an issue though with the "Preferred WiFi Uplink AP" - It is not being honoured all of the time. I have an AX11000 Pro as the primary and 2 x GT6 mesh nodes. All up to date on firmware with the 11000 on...
-
O- 12 Posts - OsagePresently I have a 1 node - 1 router aimesh system. The node is my old Asus RT-AC88U and my router is my new Asus GT-BE98 Pro. It works well but I need to set up a 2 node - 1 router aimesh system so as to obtain greater range. The nodes will/are connected to the router via wifi. Which Asus...
-
- 4 Posts - JohnoI've just acquired an AX router (AX-92U) to add to my existing AiMesh and whilst it's found by the main router (an AX-86U) in the AiMesh setup, it can't be added as a node because apparently it needs to be 2-3 metres from the root mesh node. I have the AX-92U connected via an ethernet cable...
-
- 9 Posts - jheckingI have a home AiMesh network consisting of an AX88U as the main node and an older AX56U. Until recently, everything was working fine and wireless clients would connect to the AX88U or the AX56U depending on which node was closer. Since a recent firmware update to 3004.388.7 on both nodes, the...
-
A- 3 Posts - atorchaHi, I just received the AX88U pro, but it doesn't give me Wi-Fi coverage where I need it. Before I had an AC86U as a router and an AC68U as a node. Currently I cannot have the money to buy another AX88U pro to use as a node. Which one do you recommend to install as an aimesh node, taking into...
-
R- 17 Posts - RetiredInFlHi ... just got a new ZEN WIFI Pro ET12 AIMesh.. Actually 2, the 2nd one is an AIMesh node vie ethernet backhaul. Previously had a GX-AX11000 Pro with an XT8 AIMsh node. Anyway, a strange MAC address has appeared 22:03:46:BB:0F:67 and for the life of me I can't figure out what it is. Every...
-
- 5 Posts - JohnoMy AiMesh setup consists of an RT-AX86U with two RT-AC68Us as nodes. My broadband will at some point be upgraded to full-fibre with 1Gbps download speeds, but the RT-AC68Us are only capable of a max of around 420Mbps download so I wanted to replace them with AX routers so that I get similar...
-
N- 5 Posts - nishadroxHow do I get AiMesh to switch to 5GHz uplink? Cable uplink is not an option. The main router is close enough for 5GHz. No matter how many times I reset/restart the node it still connects via 2.4GHz. Please help.
-
S- 18 Posts - SDGTRI have an XT8 system with one main XT8 and two others as nodes. I'm considering either adding two XD5 units as nodes or one XT12 as the main router and using my current main XT8 as just another node. What I'm wondering is if by adding a lower-end unit like an XD5 the entire system will drop to...
-
N- 34 Posts - neil03113 node AIMesh RT-AX88U Pro using wired backhaul with 2.5Gb ports through 2.5Gb switch (link status shows 2.5Gb). FTTH connection is 1.5Gbps. Using Smart Connect and the wireless log shows on the router shows 160M connections on 5GHz with 2Gb or better port speeds, yet speed tests through the...
-
K- 4 Posts - k9750Hello everyone hope you are all doing well ---------------------------------- Current setup GS-AX5400 ( Main Aimesh Router ) GS-AX5400 ( AiMesh node ) GT-AC5300 ( AiMesh Node ) Wifi 5Ghz is AiMesh connection ----------------------------------- my plan is to add ( GT-AX1100 ) to be the main...
-
N- 8 Posts - neatcheeI find myself in an odd situation, thanks to the folks who built my house not understanding what they were doing when they wired the place up, and I could use an outside opinion... The house was built with 6x CAT5e runs for LAN, plus another run for WAN to the fiber ONT in the garage All...
-
I- 1 Posts - iammrwongI have a pair of ASUS XD6Ss. The main unit is on the first floor and the 2nd unit is on the ground floor (connected wirelessly). I have 48 clients on the network but when I look at the AiMesh page to see what clients are connected to which node they both say 0 Both nodes are on the latest...
-
T- 1 Posts - The LoraxPrimary router is AX88U backhauled to one ZenWiFiAX ethernet and 5G backhaul to second ZenWiFIAX and wireless bridged to 1800S (remote). WiFi has been dropping once a week requiring reboot on main. The Zen backhauled on ethernet no longer connects to port and defaults to 5G wiFi backhaul. The...
-
- 3 Posts - SandmanXXI haven't seen my question answered yet anywhere else here. I have a GTAX11000 as the main router, a RT-AX3000 and a RTax88U as 2 mesh nodes. I have found that the ax3000 is transmitting 2 different ssid (2.4g and 5g) than the main router, and not passworded. Wifi analyzer shows the ssid, but... -
S- 3 Posts - SamsonHi! Please excuse me if my question has been discussed, but I am new to the forum and I haven't been able to find my exact question. I currently have a setup with an Asus TUF-AX5400 router with an unmanaged TP Link TL-SG105 ethernet switch on my 2nd floor for ethernet connection for 3...
-
J- 29 Posts - jaymizlJust about at my wit's end trying to figure this out: I Have a pair of XT9's connected via wired backhaul AiMesh at opposite ends of the house (1 downstairs + 1 up 2 flights of stairs.) and am utilising the 5GHz-2 band to connect my wireless device (macbook pro) as that is what is giving me the...
-
- 15 Posts - DGSI am experiencing AiMesh problems running over Netgear ms510tx managed switch and ethernet backhaul. My setup is - Ax88u pro 3x + A59u 1x. One Ax88u pro serves as a router and is connected to Netgear ms510tx managed switch. Nodes are connected to the switch. Currently one of the node is set to... -
M- 19 Posts - MchuzieRunning 2 AX88U PROs on latest 3.0.0.6.102_33308 firmware The secure WIFI network works beautifully on both Router and Node The guest WIFI works beautifuly only on the Router. The guest WIFI does not transmit on the Node. I only have 1 guest network and it uses the 2.5 band. Both the ROUTER...
-
X- 4 Posts - xalbsHey everyone, I'm wondering if anyone has run into this issue (i wasn't able to find anything via search) I recently added 2x ET12 as aimesh nodes to my network with a GT-AXE16000 as the main router and none of my devices are connecting to the ET12's via the 5Ghz band but 2.4Ghz and 6Ghz work...
-
M- 3 Posts - MonkePlusHello, I have a ASUS RT-AX86U and RT-AX57. I have set up a wireless AiMesh network, with the AX86U being the main router. Ever since I created the AiMesh Network, I would find my mobile device (Samsung S21 Ultra) to occasionally have a slow Wi-Fi connection to the network. By this I mean the...
-
B- 4 Posts - bbb27Hello everyone, My main router decided to reach its retirement and therefore i was thinking of getting a new setup. I was using an RT-AC86U with a pair of Lyra as nodes, and as i have learned in this forum, that was a poor choice of a setup, which i learned the hard way (i had a numerous...
-
N- 3 Posts - nortuzarSo yesterday i setup another AX58u as a aimesh in backhaul. All is working great but when i open the aimesh page to see how many clients are per unit it shows 0. In the main page it shows 36 devices. Is this a bug or something wrong with my setup? Thanks for the help
-
- 21 Posts - psychopomp1Hi, I have an Asus XT12 which I'm using as the main router and 3 plug-in 'range extender' units, RP-AX58 which are connected via ethernet to the XT12. Each RP-AX58 is plugged in one of the 3 bedrooms as wifi coverage from the main router is extremely poor because of thick walls. My internet... -
A- 2 Posts - Av3ngemeHey all, Wanted some opinions. I've got a GT-AC5300 as my main router, a RT-AC5300 upstairs acting as a node in an AIMesh setup. I'm looking to extend coverage and was looking at the XT9 AX7800 as it's triband and my nodes backhaul are connected on the second 5ghz channel currently. Will...
-
A- 2 Posts - autopilotHi, my current setup is as follows (all in AP mode, connected to Omada router)… Main unit is an AX88U with 3 XD4’s as nodes. 2 are wired backhaul, 1 is wireless backhaul (in my garage) that uses one of the other XD4’s. One of the XD4’s is dead and needs to be replaced. I’m thinking of...
-
P- 13 Posts - PowerDrI am new to AiMesh and really don't know what I am doing, but I am trying to learn. I have two RT-AX1800S's setup AiMesh with a wireless backhaul. I am connecting my PC to the node LAN port, and when I run a speed test it shows ~200 Mbps. My ISP is set at 400 Mbps and I get ~470 Mbps on my PC...
-
- 11 Posts - theirongiantI have an ASUS AX88U acting as the main router and an AC68U (aka 1900P) as an AiMesh node. I can't do wired backhaul in this place, and the wireless performance drags when the devices connect to the older AP. Since the AC68U is pretty old, it can only use 5 GHz as the backhaul and offer 2.4...
-
A- 7 Posts - amohan78I am currently confused in a particular Aimesh combo set up and need your help on the same. I have one GT-AX6000 which I am wired backhauling onto RT-AX86U Pro (Satellite Node). So I have connected the WAN port of GT-AX6000 to the ONT Modem and the LAN port of GT-AX6000 is connected to the WAN...
-
T- 19 Posts - The Cool DudeHello everyone. Hopefully someone can help shed some light on this weird issue. I have a RX-AX89X connected directly to my cable modem in the basement. I have two RT-AX92U routers set as my nodes. One on the main floor and on on the second floor. They are both hard wired with CAT6 Ethernet...
-
D- 2 Posts - Deleted member 90505Hello SNBers, if have an ASUS only AIMesh for a while now with an RT-AX86U as main router and two RT-AC68U as nodes. Everything worked fine, all the devices connected without any issues. Wifi6 (11ax) is disabled from the beginning. I now upgraded the mesh and exchanged an AC68 with a brand new...
-
S- 47 Posts - SolidSonicTHThis problem NEVER goes away and I'm tired of fighting with it. I'm going to attempt a couple more things but I'm also looking forward at this point. Can anyone recommend an alternate router that works well as an AiMesh node? I liked the firmware fidelity I got from the XT8 as an AiMesh node, I...
-
A- 5 Posts - arctanHello, I previously had AIMesh with RT-AC88U as Wireless AP / AIMesh router and Blue Cave as AIMesh node. It worked very well for me for several years (since 2019). I just decided to upgrade my router to the RT-AX88U Pro, which I set up as the new Wireless AP / AIMesh router. I reset the old...
-
F- 5 Posts - fox2dI am trying to turn my second XD6 node back into a router to use on a completely different network. I have tried using the "remove" button (which says the node will be removed and factory reset) on the admin interface and factory resetting the node with the hold WPS button method. However, each...
-
R- 7 Posts - RuinedSo, when using either the GT-AXE16000 or GT-AX11000 PRO with a wired ethernet backhaul, 160mhz channel width, and a dual band AiMesh note (eg GT-AX6000), I noticed the below behavior: Using 5GHz-1 as main mesh network SSID, and 5GHz-2 with a hidden dummy SSID: Scenario A) If main router 5GHz-2...
-
- 1 Posts - slurmsmckenzieHello, I was considering getting an RP-AX56 to add to my current AiMesh system (RT-AX86U plus wired XD4 satellite) to improve the signal for a SolarEdge inverter which has been mounted on an exterior wall. Research reveals a lot of issues seen earlier this year with this model (e.g... -
J- 7 Posts - jgv1985Hello Everyone I just placed the order for a Asus GT-AXE16000. Upgrading from my 3 year old Asus GT AX11000. I have been using Merlin Firmware on my AX11000 for a long time now and planning to use merlin firmware on the new AXE16000 once it arrives. Couple of questions: is the...
-
B- 11 Posts - BawsniaHi, Thought I would try and layout the issues I have noticed since upgrading and the behaviours in a way that may help or be similar to other people. I had a RT-AX88U as my main router in an Aimesh, the other 2 nodes were a RT-AX53U and RT-AX55. There were a few small managed Netgear switches...
-
T- 9 Posts - thewifiatemyhomeworkHello, I am a new user here but have read these forums for a number of years. Today, I have an issue that is puzzling me and while I believe I may be able to SSH into the system to change the variables, I want to confirm with the community first. Currently, I have a wired ethernet back haul...
-
A- 15 Posts - autopilotI have an Asus AX88U, 2 XD4’s and an XD4+. Set up in wireless AP mode only. Merlin on the AX88U, stock on the rest (don’t think Merlin is available for the XD4’s anyway). The XD4’s are connected to the AX88U via Ethernet, apart from one of them in my garage. The problem I have is that the...
-
- 3 Posts - TomTiddler167So, I have an existing AiMesh network, the WiFi portion is base on a pair of CT8 units. I use wired backhaul for most of it, but not all (there are 3 non-wired Lyra's used). I want to add a pair of XT9's and make use of the 802.11ax, but not entirely sure how to accomplish it. Anyone have clues?
-
Q- 5 Posts - QbcdI know this is a weird question, it's too complicated to explain why I want to know this, but basically the question is this - In an AiMesh system, if the main router fails or turns off, will the nodes still act as Wi-Fi repeaters and repeat the same SSID/pass if they get it from elsewhere? Or...
-
- 11 Posts - Phil_LibraI set 5GHz channel 36 for primary router (GT-AX6000), also enabled 160MHz, then I find all nodes (two RT-AX86U) use different channels (like 149) automatically. I found someone said this problem only exist in new firmwares from someday in 2022. I also turned the nodes to AP mode, fixed... -
R- 3 Posts - rwijnhovI allready own a gt-ax600 and have 2 ac86u aimesh nodes. I will recieve 2 gt6 tonight (230 euro after cashback) to replace the ac86u's. I have use my nodes wired. Just to be sure best way to set up would be ax6000 as master and gt6 as nodes?
-
J- 1 Posts - jksmurfI have an LED issue with an RT-AX86U Pro and an RT-AX58U AIMESH Node I.e. the main router LEDs stay off, but the node’s LEDs seem to come on after a period of time (a day). The LED switch is off for both Routers and Node in the ASUS Router App (and WebAdmin) and toggling it makes them turn off...
-
W- 8 Posts - welimHi, new to this forum. If I ask not clearly, please pardon me. 1. AIMESH main => AX88U (firmware 388.4 release) 2. AIMESH node => AX11000 (firmware 388.4 release) For the AIMESH main, I do a reboot every two days at early morning when all asleep. I expect it will also do reboot for the AIMESH...
-
- 1 Posts - eTommHello everyone. So the two XT8 are connected with ethernet backhaul and the XD6S should instead be connected with WIFI backhaul. Right now the XT8 are configured in triband smart connect and they work without any problem between them. The XD6S instead should connect to the 5Ghz-2 backhaul and...
-
B- 6 Posts - barkmarkinI just upgraded my ax58u to an AX88U Pro and I have an rp ax58 repeater as well, so I was wondering which one I should use as my other node The rp ax58 will be newer but I was wondering which is a faster option to pair with the 88u also considered the gt ax6000 but it's plain hideous and only...
-
Y- 8 Posts - yeppeyumpHi, I have three A92U, two wireless nodes. One of the nodes disconnetcts frequently, based of firmware. It not far away from main unit, and has "Great" connection as long as it works. ASUS RT-AX92U Firmware version 3.0.0.4.388_23630 - Node drops connectiont, mostly get back on track after a...
-
Q- 3 Posts - Qutrithello! Surprisingly, after some time searching through ASUS documentaiton, I haven't found a definite answer to this question: can I connect a second node to my AiMesh setup (1 m ain router, 2 Aimesh nodes) with ethernet backhaul but wire the second node to the first node for the ethernet...
-
A- 1 Posts - AndyB21I have recently moved my dual-node AX92U network to a wired backhaul (specifically Netgear PLP2000 powerline "ethernet" units) and would like to measure the actual throughput across that link. I was hoping to run the Ookla speed test on the Node to see how the throughput differed from the same...
-
M- 7 Posts - mswlogoRT-AX88U & RTAC88U Single Mesh Node Wired (Cat5e point to point) Everything is working but the Status on the AiMesh shows Yellow on connection between the two Routers with a Link to a FAQ to improve it. Why is it showing that? Is it just being dumb?
-
S- 3 Posts - SpringThingI've had terrible experience with Ax88U pro wired ethernet backhaul connected 2.5GB with Ax86u. The clients connected to the Ax86U freq. disconnects. I've tried every combination of wireless settings. The first thing I did check was that the main router, Ax88u pro, has good wireless overlap with...
-
C- 3 Posts - connkallTo sum things up quickly, I added two ET8's yesterday as nodes to my ET12 and they keep disconnecting... This would be my second (and last) attempt at Asus Aimesh. My hope is that it would work using 6E as the wireless backhaul with minimal tinkering. Both nodes get a good signal (per the ET12)...
-
R- 9 Posts - rutilateUPDATE: YES, YES IT DOES. Sent the node back to Amazon, the replacement connected first time and every time after updating firmware and resets as necessary. What a difference! So, the network is up and we're testing placements and antennae orientation for maximum coverage within the house...
-
G- 4 Posts - GabrielPhotoHi guys! Anyone has some recommendations for setting up the different bands, channels etc? I just got this router and it has so many options... Also, I have my main router, the Asus AXE16000 in my office and then in my basement I have an Asus AX11000 (non pro) connected to an ethernet cable to...
-
G- 19 Posts - gmctavishI’ve got a strange but persistent/repeatable issue in my AiMesh setup. Setup: GT-AXE16000 primary hub, hard-wired through 10G port to 10G broadband (firmware: 3.0.0.4.388_23012), and a 1G port to the nodes Two RT-AC68U nodes, hard-wired through 1G connections (3.0.0.4.386_51665) Repeatable...
-
D- 12 Posts - drabisanNo wifi expert here. Just read a bit of RFC and explanations. Considering node uses the same channels as router, adding this feature sounds like a good idea. Unlikely to mean anything for AC clients, but AX clients should show some benefits. wl0_bsscolor=0 is default, wl1 and wl2 and wl no...
-
- 15 Posts - maghuroI currently have a rt-ac86u as an aimesh node. Main router gt-ax6000. Is it worth to upgrade the aimesh node to an rt-ax53u (50€ in Portugal, 2nd hand) to replace the ac-86u? I've compared the specs and, despite the AX, the ax53u is inferior. I'm testing the ac86u as an aimesh node and I... -
O- 3 Posts - ozpacificI'm looking for a new AX router that can get giga internet broadband as is via fiber with media converter to get full giga speed. As currently my RT-AC68u router which is 9 yrs old as still running, but only getting up to 700 mbps speed, Without router, just connect to media converter (GPON) I...
-
T- 1 Posts - TeeDeeTldr - AiMesh with AX11000+AC68U or AX11000+AC88U with Ethernet backhaul causes main router to drop Internet connectivity. Router page shows WAN connected, but Networking Tools ping function unable to ping 8.8.8.8. Unable to connect to Wi-Fi, LAN devices no Internet. SSH into main router...
-
J- 6 Posts - jnmHi, I have two GT-AXE16000 routers. One primary, and one that I was trying to use as an AiMesh node. The problem I'm getting is that the node constantly resyncs and restarts wireless (as seen in its log), with only a few seconds of actual uptime in between each resync. This results in an...
-
O- 1 Posts - olivamI have spent some time to find a working solution and the right settings is pretty surprising to me. My clients were ignoring the AiMesh node even with RSSI -80 dBm on 2.4 GHz band. Long story short. Once I set up 80 MHz channel bandwidth on 5 GHz radio, it started working as requires. It means...
-
S- 2 Posts - SchneiderISI have a AX88U Pro with 2 AX86U‘s that are Ethernet backhaul connected at 2.5G. The backhaul appears to be all stable but WiFi is another issue. If I do a reboot then the wifi is good for several days and then it started to degrade at the nodes. When connected to the primary (88U) there is no...
-
I- 3 Posts - infamous_panda00Hi All, I had been running an XD4 3pc AiMesh setup for a couple of months without a single issue, with the only hiccup being that day last week where apparently Asus pushed a bad update causing the router to crash. I took this opportunity to redo my setup with a single XD6 as my router and...
-
- 28 Posts - ramishkaHi, I currently have a AiMesh setup with the following ASUS routers: AX88U: 3.0.0.4.388_22525 (Host) AX58U: 3.0.0.4.388_22525 (AiMesh Node - Connected over Ethernet) I have some random issues with the current setup: - Samsung S22U phones sometimes drop the Wifi occasionally - An iPad's... -
- 56 Posts - guruabyssAiMesh Router: RT-AX89X (Firmware: 3.0.0.4.386_47468-g73fe1fe) (Product Link: https://a.co/d/6GnccP6) AiMesh Node: RP-AX56 (Firmware: 3.0.0.4.386_42862-ga9f43cc) (Product Link: https://a.co/d/1fL9diz) Issue: Bought the RP-AX56 to expend my network, used WPS to quick connect to the node/ router...
-
- 1 Posts - ItzJbenZJust picked up the AX11000 PRO to pair with my original AX82U. Decided to go with this route instead of going with an Orbi, eero etc. I have it set up with wireless backhaul 5 GH-2. The only concern is the wifi speeds. When connected to the AX11000 PRO (Main), right next to it, I get about...
-
W- 16 Posts - w0ks2Solved: Downgrading Asus RT-AX88U from 3.0.0.4.388.22525 to 3.0.0.4.386.49674 fixed the issue. Solved: Option 2 is to enable firewall ------------------- Hardware: Using Asus RT-AX88U as AiMesh Router (3.0.0.4.388.22525, latest firmware), Using Asus RT-AX56U as AiMesh Node (3.0.0.4.386.49380...
-
T- 10 Posts - teacubedI've got NBN FTTP connected to a RT-AX88U serving as the primary router in the house. I've created an AIMESH network that's paired with a RT-AC68U in the Office and a RT-AC68U in the lounge. The Synology DS920+ is connected using two LAN cables to Port 1 and 2 of the router in the lounge and...
-
B- 5 Posts - BambinoHello everyone, I'm hoping to get some advice on how to improve the quality and speed of my home WiFi network. I currently have two routers - an RT-AC86U and RT-AX88U both on merlin+last firmware And I'm having trouble getting AI Mesh to work properly to combine them. When I want to add an...
-
- 4 Posts - Stoneware8324I have two XT8s setup as an AI Mesh in router mode. I want to change from router mode to AP AiMesh mode. I am installing an OPNsense firewall router which will be my DHCP server going forward. I'd like to change to AP mode and make the change as smooth as possible with minimal interuption to...
-
C- 2 Posts - carlpeaHi all, I have a odd issue that I've not been able to resolve over the past few days. I've had an RT-AX86U for some time, running Merlin 388.2. I've recently purchased a TUF-AX6000 which I'm using as a AiMesh node, connected on the WAN 2.5Gbps port, via a switch, to the RT-AX86U, which is...
-
- 29 Posts - TechlifterLong story short, we have a lot of smart home and wireless devices (~165) and I’ve been struggling with wireless clients (usually lights or speakers) dropping out and becoming unresponsive for long periods (45min-2hrs), only to reconnect on their own if I haven’t physically intervened by...
-
S- 13 Posts - SchneiderISI have a Asus AIMesh configuration setup with one AX88U and two AX86U's. My gig fibre comes into the detached garage where one router is placed as the primary. The other two routers are then setup as AIMesh nodes in the home with one on the main floor and the other in the basement. The home is a...
-
J- 13 Posts - jplwWith stock 388 firmware, is it possible to login to an AIMesh router and issue a command to do an AIMesh system reboot? In other words, reboot both the Router and nodes. The "reboot" command reboots only the router. I know one can ssh into each node and reboot them, but since the GUI has...
-
B- 14 Posts - Brad HAlready using one RP-AX56 for an AiMesh node and while I wouldn't call it rock solid, it can hum along for several months without any issues. And when issues do arise, most of the time I can pull it from the wall, wait a minute, plug it back in & 9 out of 10 times, it comes back on ready to...
-
Q- 12 Posts - QbcdSo I have an AiMesh system with an AX86U main router and one node. My node was an AC66U B1, which I recently replaced with an XT8. After I started using the XT8, I noticed that a lot more clients were connecting to it vs. the main router. Pretty much only the devices that are in the same room...
-
Q- 18 Posts - QbcdSort of a follow-up to my other thread where I was trying to figure out if there's a way to use the 5GHz-2 (4x4 160MHz) band on the XT8 as both backhaul and fronthaul with AiMesh. Spoiler alert - you can't. You can only use it as backhaul. Okay, so I'm using the other band for devices. However...
-
M- 11 Posts - mrblackcityHello everyone as listed in the title I have a GT-AX89X as my main router have 2 gig internet and with a 10G sfp+ copper adapter running at 2.5G to feed my node GT-AX11000. No matter what I do I cant connect no faster than 288 mbps on 5ghz on the second unit. I tried disabling the second 5 ghz...
