• SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

Recent content by i5Js

  1. I

    Guest Network Pro + VLAN 52 breaks DHCP when LACP is enabled

    Well, I figured it out — the problem was on the switch side (Cisco SG300). I had set up the Port Channel, but totally forgot to enable LACP on it. So the LAG was there, but it wasn’t negotiating properly with the ASUS. Once I set the port channel to LACP active mode, everything clicked into...
  2. I

    Guest Network Pro + VLAN 52 breaks DHCP when LACP is enabled

    It’s a problem on the management swithces, sg300. The issue is only when the devices are connected to the aimesh node. If they are connected to the main router, they can get the ip from the DHCP
  3. I

    Guest Network Pro + VLAN 52 breaks DHCP when LACP is enabled

    Thanks again Sorry but still I don’t understand what you’re trying to explain. My issue Here is, without LAPC both DHCP work fine, with LACP, DHCP of the main network works, but GNP DHCP doesn’t. I suspect there is a configuration missing in the main router or the management switches
  4. I

    Guest Network Pro + VLAN 52 breaks DHCP when LACP is enabled

    Hey. Thanks for your message, I’m sorry, but I don’t understand. DHCP is enabled in GNP profile and LAN, for the main network. DHCP in GNP network was working fine till I activated LACP in the router
  5. I

    Guest Network Pro + VLAN 52 breaks DHCP when LACP is enabled

    Hi everyone, I'm running an ASUS AXE16000 with Merlin firmware and have several VLANs set up at home. One of them is VLAN 52, which I use with Guest Network Pro for a dedicated WiFi network for the kids. Everything works fine when I connect the router to my switch (a Cisco SG300-28) using a...
  6. I

    3006.102.5 Guest Network Pro issues in Aimesh nodes after reboot

    Hold on, I had to configure the SG300-10 to allow the VLAN on ports 5 and 7 too Man, I don't know... again, I'm not expert in networking but... it works. , I still don't know why it doesn't work with LACP, or what is missing in the ASUS settings...
  7. I

    3006.102.5 Guest Network Pro issues in Aimesh nodes after reboot

    Hey, I have two sg300 (big house with existing lan cables)So, without LACP: from ASUS LAN1 to SG300-28 LAN1, from SG300-28 LAN 17 to SG300-10 LAN 5 and finally from SG300-10 LAN 7 to Asus Mesh node. That works fine, without LACP With LACP, I presume there is something missing in the ASUS...
  8. I

    3006.102.5 Guest Network Pro issues in Aimesh nodes after reboot

    Hello, Well, this is what I did in my sg300-28 Create the VLAN Choose the port that connects to the Amesh node, and set the following settings: Go to the Port to VLAN settings and should be like following: Go to Port VLAN Membership, and should be like following: And that's it... then it...
  9. I

    3006.102.5 Guest Network Pro issues in Aimesh nodes after reboot

    Finally I made it!. It's late here, so tomorrow I will share the details to configure a SG300-28 in between.
  10. I

    3006.102.5 Guest Network Pro issues in Aimesh nodes after reboot

    I've changed/tried different settings in the sg300, nothing has worked. I'm starting to think it never will with managements switches.
  11. I

    3006.102.5 Guest Network Pro issues in Aimesh nodes after reboot

    Agreed, I will check all the sg300-28 settings to disable :) or I will reset it again
  12. I

    3006.102.5 Guest Network Pro issues in Aimesh nodes after reboot

    Hey, thanks Yes the nodes support it, with a non management switches, everything works
  13. I

    3006.102.5 Guest Network Pro issues in Aimesh nodes after reboot

    New tests, but same results.... I can't get an ip from the mesh node, I've reset the switches to the default settings, and L2, it didn't work. With dumb switches, it works. Honestly, I don't know what else I should need to configure in in the management switches to make it work
  14. I

    3006.102.5 Guest Network Pro issues in Aimesh nodes after reboot

    Thank you very much for the response. That’s exactly where the problem is. I believe the node is broadcasting the SSID correctly, because devices can connect to the network, but they don’t get an IP address from the DHCP server. However, if they connect to the main router, they do get an IP...
Back
Top