Menu
What's new
By:
Filters Better Search

Search results

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

  1. Booboo22

    goCoax MoCA 2.5 adapter

    Wait, this "basement MoCA adapter tv port - > coax to second floor -> second floor MoCA adaptor moca port" doesn't sound right. The TV port on MoCA adapters typically only pass the low-band 5hz-1Ghz TV frequencies not pass MoCA signal (which is above 1Ghz). In other words, that TV port is only...
  2. Booboo22

    goCoax MoCA 2.5 adapter

    Ah, sorry I didn't realize that. Now, just to make sure it's not a cabling problem, you *could* just disconnect all the MoCA 1.0/1.1 devices off the coax and try again. Do that and you will then be convinced that the coax is *not* the issue.
  3. Booboo22

    goCoax MoCA 2.5 adapter

    I didn't mean run new coax but rather, since you already have the two adapters connected via coax runs, go to the attic, basement, or other location where all the coax runs converge and main splitters are located, find those two coax runs, and connect them together. That's what I did.
  4. Booboo22

    goCoax MoCA 2.5 adapter

    Just out of curiosity, do you really need to be running these in the same cable plant as the MoCA 1.1 devices? I needed to extend an Ethernet connection across the house; for that i'm using MoCA 2.0 bonded and I simply connected the coax drop from the garage (where one adapter is) to the coax...
  5. Booboo22

    goCoax MoCA 2.5 adapter

    In MoCA one device is the "Network Coordinator" since the architecture is CDMA/CD; it's responsible to sending the beacon. Beacons (bits of network information) are used for devices to join the network. Typically you should not enable Preferred NC and allow the adapters to auto-negotiate who...
  6. Booboo22

    goCoax MoCA 2.5 adapter

    Also, why is network security enabled on the D-Ext but your MoCA setup shows the "In Scan List" on the D-High?
  7. Booboo22

    goCoax MoCA 2.5 adapter

    According to your first image, that specific adapter is getting and dropping lots of bad Ethernet frames. Does the other adapter also show bad Rx frames?
  8. Booboo22

    goCoax MoCA 2.5 adapter

    You're not going to get better than that for point to point, as the Ethernet NIC is GigE. But since MoCA is shared medium, you can get a better aggregate throughput for multiple devices.
  9. Booboo22

    Locating cable modem BEFORE moca poe filter and splitter

    Neat! I have the Zyxel 2.0 bonded and achieve 940Mbps between two devices without issue. Can I ask why you are even connecting that MoCA Splitter to the rest of the coax? Why not simply connect the two MoCA runs with a barrel connector? That's what I did :)
  10. Booboo22

    Locating cable modem BEFORE moca poe filter and splitter

    If there's no MoCA requirements on your cable modem, then I would say Option B is better. Having the PoE Filter as described on B allows better signal strength (less dB loss due to reflection on the PoE) between MoCA Adapters. Which MoCA version are you attempting to deploy? MoCA splitters...
  11. Booboo22

    linux based NAS os'es

    I use HP MicroServers as the NAS linux boxs as shown below. The HPs are AMD N40 dual core, low power 1.5Ghz CPUs, with 8GB of RAM. Each boots off SSD and has up to 4 SATA HDDs. GigE nic. The router is separate and out-of-scope for OMV.
  12. Booboo22

    linux based NAS os'es

    OpenMediaVault has been great, using for about 5 years. it just works....
  13. Booboo22

    ECB6200 not showing node info

    This seems related to javascript perhaps?
  14. Booboo22

    ActionTech ECB6200 MOCA adapter , not getting full speed

    Any updates ?
  15. Booboo22

    MoCA2.5 adapters is coming

    Please tell us more once you put into production. Do these units have a web UI for checking firmware, frequency bands, phy connect rate, etc.?
  16. Booboo22

    Zyxel HLA4205 GUI?

    Anyone know if the HLA4205 MoCA 2.0 adapters have a web UI? I couldn't find any information on the docs, but usually this is not documented.
  17. Booboo22

    ActionTech ECB6200 MOCA adapter , not getting full speed

    Another suggestion, disconnect your cable modem off that splitter, and disconnect from the POE altogether. Run the iperf test with just the MoCA devices on the cable plant. Then we might know if there's something with the incoming cable signal, the cable modem, or the cable plant... Just the...
  18. Booboo22

    ActionTech ECB6200 MOCA adapter , not getting full speed

    I think you need to further map your home coax layout. Any unused coax cables should be removed from the splitters and those ports on the splitters terminated. Alternatively, you can terminate the open ports on the walls. Also, if your signal coming from the cable company is too hot (high)...
  19. Booboo22

    MoCA2.5 adapters is coming

    It's a switch... just like your Ethernet switch has multiple ports. So two computers, one on each 1GigE port could be transmitting/receiving at full speed and the uplink (MoCA 2.5) would transport those two sessions.
  20. Booboo22

    MOCA noob needs advice

    Unless the cable lengths are exceptionally long for a home, or the RG-59 is damaged, it should work with MoCA 2.0. Even non-MoCA 2.0 splitters tend to work just fine, the technology is very forgiving. I would concentrate to ensure the frequency bands are not overlapping with your cable modem...
Top