Menu
What's new
By:
Filters Better Search

Search results

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

  1. S

    Skynet Skynet - Router Firewall & Security Enhancements

    Does anyone know how to fix this? ############################################################################################################# # # #...
  2. S

    WAN_Connection: ISP's DHCP did not function properly.

    Thanks L&LD, all working great so far
  3. S

    amtm amtm - the Asuswrt-Merlin Terminal Menu

    Oops! I see it now on the WAN page. Thanks
  4. S

    amtm amtm - the Asuswrt-Merlin Terminal Menu

    Is there a more in depth explanation somewhere, as to why DNScrypt and Stubby have been depricated in AMTM? Thanks
  5. S

    WAN_Connection: ISP's DHCP did not function properly.

    3 weeks without issue and I had one lockup 3 days ago, but none since. I wiped it clean, then went back to stock firmware and ran that for about a week before going back to Merlin. I haven’t setup optware yet either, I left that off and VPN. If after VPN test it still works I will load optware...
  6. S

    WAN_Connection: ISP's DHCP did not function properly.

    Do you have VPN enabled? I followed L&LD’s post and l haven’t had a problem so far. I’m going to enable a VPN in a couple of days and i’ll See if that’s the issue. So far there is no root cause only speculation unfortunately
  7. S

    WAN DHCP Connection Issues 384.10* Firmware

    Thanks, I'm going to give it a shot
  8. S

    WAN DHCP Connection Issues 384.10* Firmware

    I will try that. I'm still back on stock FW, but I'm going to try again following L&LD's post with just a basic setting and then add all my static IP's, port forwarding and VPN one at a time, letting it run a couple of days in between.
  9. S

    WAN DHCP Connection Issues 384.10* Firmware

    Exactly, word for word
  10. S

    WAN_Connection: ISP's DHCP did not function properly.

    Thanks I will try the rebooting steps. I did everything else except reformatting the Jffs partition (I assumed factory reset and stock firmware load in rescue mode would wipe that)
  11. S

    WAN_Connection: ISP's DHCP did not function properly.

    OK, here is what happens on mine: My ISP is Cogeco.ca and I have a Cisco DPC3848VM modem which I setup in Bridge mode. I use my Asus RT-AC3200 which has been working fine for the last couple of years. Recently however it started dropping connections, occasionally in build 384.8, more so in...
  12. S

    WAN_Connection: ISP's DHCP did not function properly.

    It was pretty long and I didn't want to hijack yours
  13. S

    WAN_Connection: ISP's DHCP did not function properly.

    This is happening to me as well, I just added a post about it
  14. S

    WAN DHCP Connection Issues 384.10* Firmware

    I am also have similar issues to what I have seen in some of the posts and have actually had to go back to stock firmware to fix it. My ISP is Cogeco.ca and I have a Cisco DPC3848VM modem which I setup in Bridge mode. I use my Asus RT-AC3200 which has been working fine for the last couple of...
  15. S

    Help - USB Health Scanner - Scan Results Blank

    I use it for entware and also for backing up my syslog and other log files, my jffs backup etc. I have 3 partitions ext3 for entware , swap, fat32 for data (so I can directly mount in windows or OSx if I need to) I usually use rescan under Health Scanner. The other option would be to ssh into...
  16. S

    Help - USB Health Scanner - Scan Results Blank

    I have an ASUS RT-AC3200 running FW 384.6. I have a SanDisk Cruzer 8Gb USB on the USB 2.0 port, which is all working fine. Sometimes the router will lock-up and I have to perform a hard reboot. When this happens, my USB doesnt always mount, so I have to unplug and re-attach. When I run the...
  17. S

    NTP Daemon for ASUSWRT/Merlin

    All is working fine but the graphs are just blank, I completely uninstalled and reinstalled and everything is working, except for the graphs which do not update, they are blank
  18. S

    NTP Daemon for ASUSWRT/Merlin

    Can anybody post libpng12.so so I can get the rddtool to work. Thanks
  19. S

    [SOLVED] Change default shell from sh to bash (378.56_2)

    That worked! Thanks for the help BTW, I found that adding the .bashrc command below cp /tmp/mnt/data/.bashrc /tmp/home/root/.bashrcto jffs/scripts/services-start didn't always work, but adding it to /jffs/scripts/post-mount always works
  20. S

    [SOLVED] Change default shell from sh to bash (378.56_2)

    Thanks Merlin, I tried that, don’t get the error anymore but still doesn’t read .bashrc without putting source in front. I was reading that sometimes bash does not read the file, so I was thinking I should put that in a startup script, but not sure which one I copy the .bashrc from my USB once...
Top