Menu
What's new
By:
Filters Better Search

Search results

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

  1. J

    vnStat [Release] vnStat-on-Merlin - UI, CLI and email - data use and data limit monitoring - R1 and R2

    What does NTP watchdog script do?
  2. J

    DNS over TLS can't seem to verify

    Is there a better test site?
  3. J

    Beta Asuswrt-Merlin 386.3 beta is now available

    2) Would VPN2 and VPN3 need to be set to ON? Or could I leave them OFF ("Stop Client"), and the router would switch them ON automatically if VPN1 goes down and it is looking to enforce policy rule no 2? The yes to question 2 could go either way. Is that yes to the first part of the question or...
  4. J

    Beta Asuswrt-Merlin 386.3 beta is now available

    Quick testing on Beta3 (dirty upgrade) dbfafff825 openvpn: only set error state in nvram on fatal config errors seems to have fixed my VPN issue we discussed and seems to be working as expected now.
  5. J

    amtm amtm step-by-step install guide - L&LD

    OK, this is definitely not best practice, but I just dirty upgrade, no dismount USBs (I have 2 attached) nor disconnect. It usually just works. So, I wouldn't worry about it. Been doing this on RT-AC68U and later RT-AC86U). Also, every now and then (say every 10 dirtys), I'll do a rebuild...
  6. J

    Beta Asuswrt-Merlin 386.3 beta is now available

    Thanks
  7. J

    Beta Asuswrt-Merlin 386.3 beta is now available

    I am having issues with VPN (note, I'm in contact with RMerlin with logs, etc). He mentioned that it could be a script interfering (although he reviewed my running scripts and didn't think any would interfere). I was wondering if there is a way to start the router without scripts (similar to...
  8. J

    Beta Asuswrt-Merlin 386.3 beta is now available

    I sent you a PM with Pastebin of the log
  9. J

    Beta Asuswrt-Merlin 386.3 beta is now available

    It worked under 386.2_6. In fact, I downgraded back to it to test just to make sure. When I reloaded 386.3 beta2, doesn't work (even though it shows connected in Status). I have 5 VPN servers set up (for different countries), no rules. If I just click #5 to connect, should all traffic go...
  10. J

    Beta Asuswrt-Merlin 386.3 beta is now available

    I upgraded from 386.2.6 to 386.3beta2 (dirty), however, I can not seem to get the VPN to work. When I select the VPN Client service state to on, (it shows connected) and I go to a IP address check page, it still shows my local IP USA address (not the foreign country's-ex UK). I have tried...
  11. J

    scMerlin scMerlin v2 - Service and script control menu for AsusWRT-Merlin

    OK, I turned on watchdog and rebooted. Booted OK. So I kept watchdog on. Rebooted 5 more times. 1 time I had the weird errors (missing CRONs and short log file) but other times it didn't. So, I don't know what is going on. I did copy the syslog file when I had the error, but I'm not sure if...
  12. J

    scMerlin scMerlin v2 - Service and script control menu for AsusWRT-Merlin

    There is a syslog.log and a syslog.log-1. However, I have since switched watchdog off and rebooted the system to get to a full system. If you want me to, I will set watchdog on again and reboot, but I can not do this until tonight (when people will not be on the system). If yes, please...
  13. J

    scMerlin scMerlin v2 - Service and script control menu for AsusWRT-Merlin

    I use scribe and uiscribe. Usually, when I reboot, there are 1300-1400 or so lines, but when the watchdog script was on, I was only getting 80-90 lines.
  14. J

    scMerlin scMerlin v2 - Service and script control menu for AsusWRT-Merlin

    Good point, thanks
  15. J

    scMerlin scMerlin v2 - Service and script control menu for AsusWRT-Merlin

    part 2 Jun 1 04:34:23 wlceventd: wlceventd_proc_event(527): eth5: Auth FC:6B:F0:57:9F:3E, status: Successful (0), rssi:0 Jun 1 04:34:23 wlceventd: wlceventd_proc_event(556): eth5: Assoc FC:6B:F0:57:9F:3E, status: Successful (0), rssi:0 Jun 1 04:34:24 kernel: DROP IN=eth0 OUT=...
  16. J

    scMerlin scMerlin v2 - Service and script control menu for AsusWRT-Merlin

    So I rebooted, again, 4 or 5 cron jobs did not load init-start is: #!/bin/sh sh /jffs/scripts/ntpbootwatchdog.sh & # scMerlin My whole syslog is as follows (it seems like there should be more but this is all there is Syslog is only 89 lines, too long to post in one post so I will split it to...
  17. J

    scMerlin scMerlin v2 - Service and script control menu for AsusWRT-Merlin

    So init-start is just 1 line (before turning on watchdog script) #!/bin/sh So, I tried it again, went to scMerlin, turned watchdog script on, clicked the save button, rebooted my router..........and everything loaded OK this time! I really didn't do anything different. I can not explain it...
  18. J

    scMerlin scMerlin v2 - Service and script control menu for AsusWRT-Merlin

    I'm not an expert, but this sounds right. Is there any issue placing the watchdog to run after all the other jobs are loaded? Then it would not interfere with the others?
  19. J

    scMerlin scMerlin v2 - Service and script control menu for AsusWRT-Merlin

    I'm running on an AC86U also, don't know. All I know is I turned it on and rebooted, and some cron jobs didn't run, shut off, everything fine, turned on, same, shut off fine, tried again, same, off, fine. Now, each time I ran it and rebooted, there was a different set of cron jobs...
  20. J

    scMerlin scMerlin v2 - Service and script control menu for AsusWRT-Merlin

    Well, it doesn't boot correctly when the watchdog script is set, but if fine when it is not. I've shut it off, maybe others can comment if it is working OK for them.
Top