Search results

I am in a very similar position except my main router is an RT-AC3100. Right now I run no nodes but I probably need one for the backyard area. Lets say I went with a rt-ax88u pro to be my main. Would the rt-ac3100 as a node make the rt-ax88u pro work worse as the main? I.E. would their be...

Thanks! I don't think i can get into the ONT log. This seems like a new issue in the past two weeks and there have been no hardware changes since the service was installed. I can change the ethernet though i was thinking of moving my router to a different room anyway!

So I am posting this here because of this line in the syslog: Nov 15 06:46:58 RT-AC3100-14D8 custom_script: Running /jffs/scripts/service-event (args: restart wan_if) and: Nov 15 06:47:01 RT-AC3100-14D8 custom_script: Running /jffs/scripts/service-event-end (args: restart wan_if) But really I...

I am moving next month and wondering how my current config will handle the new place. Right now I have starlink Internet avg 120mbps down. Rt-ac3100 is my hub with 3 hard wired rt-ac1900 as nodes. My main runs Merlin. My current apartment is 2300 sqft but very sprawling with foot thick walls...

cool yes, i think i can handle that- just barely but all of that makes sense i see those backups in the gui and yeah i can tar the usb.. i wonder the most optimal procedure in terms of the "living" relationship between the jffs partition and the usb this would this work: use the gui to...

i guess the essence of this is i thought more of the merlin add-ons/extras/goodies went on the usb. It just takes a while to set up the swap, the entware, diversion, unbound, which is all i have now... i envision adding the qos stuff and perhaps the skynet. Anyway since I thought more/all of...

okay i got that.. how about this: i have an rt-ac3100 that is all set up with all the merlin goodies running. can I clone that to another rt-ac3100? i.e. is there something on the system that I can backup/clone/mirror so that in the event of a blowout there is easy recovery?

In looking around for solutions for which usb to use for the swap and such I wondered about my server where my boot device is basically a mirrored zfs pool with two small msata drives. Now I know that my server has a lot more horsepower to do the software raid. I am still wondering about any...

Hello All, So I am trying to configure my rt-ac3100 (currently on the latest beta firmware) with dual wan set up. I would like my primary WAN to be Starlink. I would like my secondary "fallback" WAN to be my DSL ISP. My Set up is as follows: Here are what the two configurations look like...

Yep the first power cycle didnt do it. But another power cycle did work after I turned off the backhaul mode. So with the switch I can maintain what I had before the firmware update: nodes connected via switch. But with backhaul mode enabled I could not get my nodes behind the switch to connect.

Same as Mark for me too.

The GUI reports that I cannot change or view the config of the nodes as they are disconnected. I had disabled the ethernet backhaul and power cycled the not connected nodes and cannot get them back connected yet. edit: i also cannot ping the nodes from the ac3100

I did set the connection priority to 1G WAN first on my nodes. The one that is working still has that setting. I did enable the ethernet backhaul mode and so the wired node is working fine in that mode. So should my two nodes that are connected via the switch not work in ethernet backhaul...

I have a question about the new ethernet backhaul optimization settings and the use of a network switch. So from the image you can see I have a rt-ac3100 as the main and then 3 nodes. The node that shows up in the image as "working" is hardwired directly from the rt-ac3100. I have a netgear...

With all the time at home I am trying to complete a backhaul project and wondering about this setup: Currently I have dsl (slow) internet modem going to rt-ac3100 with 4 rt-ac68 as nodes. One of the rt-ac68 is hooked up via ethernet backhaul the other 3 are wireless nodes. I got two peplink...

Hey all, Question on how the aimesh Nodes connect back to main router. If I have a wireless node can I connect another wireless node to that one further away from main router or does a wireless node always have to hit the main router. Same question but with wired. Can I connect a node via lan...

Thanks Grisu! Keying me in on the 376-3626. Since I am using a rt-ac68r I wanted to get that version which I found here: https://drivers.plus/de/asus-rt-ac68r-router-firmware-3-0-0-4-376-3626/233429/ I had to vpn to Germany to download it but once I uploaded that in the gui it took and then I...

Well the solution there doesn't work at least when I try to upload the latest firmware or the oldest firmware available on https://www.asus.com/supportonly/RT-AC68R/HelpDesk_BIOS/ well I have solved the problem of why i don't have aimesh... i am running firmware from before that upgrade. Now I...

oh man actually in exploring firmware... it seems that I did not get any update to apply. I am actually at 3.0.0.4.374_205 I might be experiencing this: https://www.snbforums.com/threads/rt-ac68u-firmware-stuck-at-205.14341/

Asus serial number reports: Wireless-AP RT-AC68R DBIRGO000191 Out Of Warranty 2015/11/26