Menu
What's new
By:
Filters Better Search

Search results

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

  1. maxiarg14

    Router Traffic (192.168.X.1) not going through the VPN?

    HI @Yooshaw , yes, you have to modify config of Pyload and Transmission to set them to listen on router ip (192.168.1.1 on my case), and not 0.0.0.0, that means listening on all interfaces. And of course set policy rules in VPN Client to pass trough VPN all packets comming from 192.168.1.0/24...
  2. maxiarg14

    Add router IP to use VPN using Policy Rules

    @eibgrad It works!!! I bound Transmission and Pyload to only listen on 192.168.1.1 (both were listening on all interfaces, 0.0.0.0). Now I can see in Transmission that my ip is the one provided by my VPN service: I don't know how to check that Pyload is using the same IP too, DO YOU KNOW...
  3. maxiarg14

    Add router IP to use VPN using Policy Rules

    I think I have to create a virtual lan, isn´t? Create a virtual interface and make Transmission and Pyload to listen on that interface, and then add routes so I can go to internet through that interface. I'm not an expert, maybe I need a tutorial to understand more the situation. Sorry for my...
  4. maxiarg14

    Add router IP to use VPN using Policy Rules

    Hi @eibgrad , that makes a lot of sense, and I was thinking the same. Do you have any tutorial or explanation of how to do that? It seems to be complicated, or not? Thank you for the answer! Best regards
  5. maxiarg14

    Router Traffic (192.168.X.1) not going through the VPN?

    Hi @Yooshaw ! I'm dealing with the same issue. All clients on lan go to Internet trough VPN, but not the router itself. Did you find any solution for this??? Thanks on advance. Best regards!
  6. maxiarg14

    Add router IP to use VPN using Policy Rules

    Hi to all! I just installed Pyload and Transmission on my RT-AC86U. Now I have a problem. I have to set the router (192.168.1.1) to go to Internet through VPN and NOT through WAN. How can I do that? I have the policy rule: All 192.168.1.0/24 0.0.0.0 VPN So it's supposed to do the job...
  7. maxiarg14

    Entware python2 entware

    I just found an archive of entware that contains the 2.7 version for my hardware (https://bin.entware.net/aarch64-k3.10/archive/prev/). Thank you very much friend!
  8. maxiarg14

    Entware python2 entware

    @atomizasser Thank you very much! I was thinking on install it manually, but I didn't find the file. I have one more question. I have the RT-AC86U, that has armv8 processor. That version for armv7 will work for me?? I think I have to download the version for my hardware. Can be...
  9. maxiarg14

    [TUTORIAL]pyLoad Download Manager through Entware

    Hi to all! I'm trying to install PyLoad via Entware on my Asus RT-AC86U, but only Python 3 is available and PyLoad works only with Python 2. Can anyone help me? Thanks and regards!
  10. maxiarg14

    Entware python2 entware

    Hi @atomizasser ! Did you find any solution for this? I'm dealing with the same issue. Thanks! Regards
  11. maxiarg14

    [DSL-AC68U] AsusWrt Merlin builds for DSL routers

    Hi @SeamusMAcSpud ...did you find any solution for this issue? Is happening exactly the same to me, but with RT-AC86U. I've enabled all settings for multicast optimization (IGMP Proxy, Snooping, etc), but nothing works. Thanks, Regards!
  12. maxiarg14

    RT-AC86U Merlin IGMP Snooping mcpd.conf

    Hi @skeal, no, is working very well with every wireless device. In fact, I use a Netgear WNDR3400 with tomato firmware in "Wireless Ethernet Bridge" mode, and works perfectly with the main router (the RT-AC86U). If I connect the STB to the Netgear via wired ethernet, it works perfectly too...
  13. maxiarg14

    RT-AC86U Merlin IGMP Snooping mcpd.conf

    Hi! I have an ASUS RT-AC86U with Merlin Firmware 384.13_0. I couldn't receive IPTV until I enabled IGMP Proxy. Now I can play the content, but after 2 minutes the image freezes, and I have to change the channel to receive content again, and then after 2 minutes the image freezes again. I...
  14. maxiarg14

    RT-AC86U - Enable efficient multicast forwarding (IGMP Snooping)

    What version were you using when you wrote this? I'm doing the same as you, but image freezes after 2 minutes. I think is a snooping issue. Thanks! Regards
  15. maxiarg14

    Netgear WNDR3400 Wireless Ethernet Bridge Multicast Issue

    Hi! I'm using a Netgear WNDR3400 v1 with FreshTomato firmware installed (K26USB-NVRAM64K_RT-N5x-MIPSR2-2019.1). This device is configured with "Wireless Ethernet Bridge" mode, and is connected via wireless to my main router (Asus RT-AC86U with Merlin Firmware). I have an IP STB Box to receive...
  16. maxiarg14

    NVRAM Variable not updating.

    @Asad Ali Thanks for answer. Yes, that is what I´m doing, but for some reason that command is not working until the line "Initialization Sequence Completed" appears in the log, so when running the script "usr/sbin/gettunnelip" from inside my script, it returns an "unkown" ip. Now I'm not at...
  17. maxiarg14

    NVRAM Variable not updating.

    @Martineau, @RMerlin do you have any other suggestion? The curl command is start working after "Initialization Sequence Completed", the same if I call "usr/sbin/gettunnelip.sh". Both commands starts to work after the initialization is completed, no matter what sleep delay I set, so I can't get...
  18. maxiarg14

    NVRAM Variable not updating.

    Hi @DFFRZ, @Asad Ali Did you find any solution for this issue? Exactly the same thing is happening to me. I tried the curl command suggested by @Martineau too, but is still not working. It seems that ip is seted after this line in the log is executed: "Initialization Sequence Completed"...
Top