Menu
What's new
By:
Filters Better Search

Search results

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

  1. 1

    ANNOUNCEMENT: Asuswrt-Merlin support underway for 3 Wifi 7 routers

    Based on this it sounds like best to keep to latest firmware. But in this instance, is Merlin 3004 or Asus 3006 considered the latest firmware?
  2. 1

    ANNOUNCEMENT: Asuswrt-Merlin support underway for 3 Wifi 7 routers

    Hi, sorry am new to these and have been blindly updating Merlin firmware on my ax6000. I just recently noticed that I’m on 3004 Merlin while Asus is on 3006. I read the corresponding thread on why this is the case and the complexity and time needed to get 3006 to be developed on Merlin. What...
  3. 1

    settings for AX11000 pro

    There will be no ap in switch 3. Just direct to the switch 3 there. The router will remain at where the living switch is. Will this change anything. Getting confusing here haha. Unfortunately it sucks that my isp need a dedicated vlan for iptv.
  4. 1

    settings for AX11000 pro

    The iptv will definitely need vlan 20. So if I don’t need iptv, dumb switch will do. If I need iptv then a managed switch will be needed and does the configuration goes like this? The new switch configure in the attached. Db switch : vlan10 port 1,2, 6 tagged, port 3 untag vlan 20 port 1,2, 6...
  5. 1

    settings for AX11000 pro

    Thanks everyone for your help. I have shifted the hdd to my shield directly and ram is 60% now. Assuming one of the AP is located in another room and I need 3 LAN point, I assume I can just get an unmanaged switch and that should work? Unless I need the iptv into that AP room, then I will need...
  6. 1

    settings for AX11000 pro

    and anyone has any idea why is the ram so high?
  7. 1

    settings for AX11000 pro

    not very technical with this, but where do i run these from?
  8. 1

    settings for AX11000 pro

    Hmm I think I’m getting you but just to be sure, what is the ip of the vlan 100? Is the ip in vlan 10 and vlan 100 the same? I suspect the static ip I assign to the switch is from vlan 10 which has the internet and was hence asked to turn off gateway. We are getting there!
  9. 1

    settings for AX11000 pro

    What I meant is that the switch I assign static ip within the lan ip and setting gateway to 0.0.0.0 to prevent “internet” from getting into the switch for security issue.
  10. 1

    settings for AX11000 pro

    How do I figure out the mW?
  11. 1

    settings for AX11000 pro

    Yea so I have setup static ip which is within the router and isp domain so that I can configure them from any pc which is within the network. Only the gateway is set to 0.0.0.0. If I were to set a ip outside of the isp range, every time I need to configure the switch, I will have to manually...
  12. 1

    settings for AX11000 pro

    im in singapore. what is the mW in this country and where and how do i set those? i was caught in a dilemma between this router and the ax6000. the situation was that ax6000 was going for $386. but my credit card was having a promo where you spend $599 and you get back $500. the ax11000 pro...
  13. 1

    settings for AX11000 pro

    should i then disable it to improve my range? sounds like they will interfere with each other? i suppose the 3rd band we are talking here is the 5g-2. if it is set aside for vr set or backhaul, what happens when i connect normal devices like phone and tablet to it?
  14. 1

    settings for AX11000 pro

    Thank you so much for the tips and advice so far! yes that is correct, vlan 10 is for the ISP and vlan 20 is for the iptv. im actually in singapore and our ISP (Singtel) need a specific vlan separated from the main WAN for their IPTV hence 20 was created. i created a guest ssid wifi network...
  15. 1

    settings for AX11000 pro

    sorry not very well versed in this so i hope this is correct now. universal beamforming and tx bursting disabled on 2.4ghz, 5-1 ghz, 5-2 ghz. disabled 160mhz and dfs for 5-1 ghz.. <- can i just check any reason for unchecking 160mhz? disabled 160mhz for 5-2 ghz but there is no option appearing...
  16. 1

    settings for AX11000 pro

    ok is this correct with the revised? is so, i will monitor them for abit. let me know if i did them wrongly. there are no ap connected to it currently. also, are there any settings for the router wireless that i need to be aware of? lastly, hdd attached to router and ram usage is 95%... thats...
  17. 1

    settings for AX11000 pro

    i cant seem to delete vlan 1. its default and it doesnt allow me to 'delete' it as its grey out. the hang seems to happen on only my iphone 12 mini. streaming devices like Nvidia shield (wifi) has no issue. pc via wired has no issue. no one else in the family complain hang on their...
  18. 1

    settings for AX11000 pro

    Hi all Im on merlin firmware - 3004.388.4_0_rog recently changed my router from ax58u to ax11000 pro. while i noticed some 'minor' improvement such as speed and coverage range (i was expecting more actually), at certain times im experiencing a network 'hang' for a couple of seconds before...
  19. 1

    Issue with Asus rt-58u help please

    Hi just recently change my router from tp link ax10 to Asus ax rt-58u. previously ax10 was on wpa3 and all my device can be connected. now with 58u, half of my device cannot connect to wpa3, wpa2. However, I created guest network and set to wpa2, those device that can’t connect to wpa3 and 2...
Top