Belkin CFE recovery errors?

[Attinder]

Hi, I am trying to recover a router I purchased from eBay. It's Belkin F9K1124 AC1900. I tried to recover with UART but this is not recognising any commands. I pressed esc while booting and this is what I booted up to. It's not CFE as other websites mention. Resetting with TFTP by pressing reset button didn't work either. Can anyone help me with this? It does recognise reboot command. For anything else it says Unknown command.


Boot LOG:

BBoooottiinng.

DRAM Type: DDR3

DRAM frequency: 580MHz

DRAM Size = 128 MB

@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

@

@ chip__no chip__id mfr___id dev___id cap___id size_sft dev_size chipSize

@ 0000000h 0c22018h 00000c2h 0000020h 0000018h 0000000h 0000018h 1000000h

@ blk_size blk__cnt sec_size sec__cnt pageSize page_cnt chip_clk chipName

@ 0010000h 0000100h 0001000h 0001000h 0000100h 0000010h 0000048h MX25L12805D

@

@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@


---Realtek RTL8198C boot code at 2016.03.25-21:45+0800 v1.5g (1000MHz) [C0 running][C1 sleep]

Done!

DEBUG_INF: Index Name Offset Length Real_Offs Real_Size

DEBUG_INF: 0 boot 0 20000 0 20000

DEBUG_INF: 1 cal-data 20000 10000 20000 10000

DEBUG_INF: 2 data-psi 30000 10000 30000 10000

DEBUG_INF: 3 data-voatile 40000 10000 40000 10000

DEBUG_INF: 4 nvram 50000 10000 50000 10000

DEBUG_INF: 5 nvram-bak 60000 10000 60000 10000

DEBUG_INF: 6 kernel 70000 200000 70000 200000

DEBUG_INF: 7 rootfs 270000 b00000 270000 b00000

DEBUG_INF: 8 reserved d70000 290000 d70000 290000

SC LED BLINK INIT.


---Escape booting by user, Get into CLI earlier


---Ethernet init Okay!

<RealTek>boor

Unknown command !

<RealTek>boot

Unknown command !

<RealTek>tftpd

Unknown command !

<RealTek>help

Unknown command !

<RealTek>A

 

[sfx2000]

Hi, I am trying to recover a router I purchased from eBay. It's Belkin F9K1124 AC1900. I tried to recover with UART but this is not recognising any commands. I pressed esc while booting and this is what I booted up to. It's not CFE as other websites mention. Resetting with TFTP by pressing reset button didn't work either. Can anyone help me with this? It does recognise reboot command. For anything else it says Unknown command.

It's not CFE - it's Realtek's bootloader - it's been a long time since I've looked at Realtek's Router/AP SoC's, but if I recall correctly, they build their SDK from OpenWRT.

Here's a good link to get you started...

https://github.com/cgoder/openwrt_rtk

Take a look here for good info from Realtek

https://github.com/cgoder/openwrt_rtk/tree/master/original/document

Enjoy!