Menu
What's new
By:
Filters Better Search

Search results

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

  1. D

    Quandry on gear choices

    I’m looking to stay in the ASUS line - have had multiple years of experience with Merlin firmware and the experience has been largely good. Don
  2. D

    Quandry on gear choices

    Not exactly. I have single runs from the WAN router location to each of the AP locations and will likely run Merlin on at least the WAN router and use AI Mesh (at least try it again) to ASUS firmware APs. Daisy chaining won’t work and I don’t really want to pull new wire.
  3. D

    Quandry on gear choices

    Looking to upgrade existing network with AX compatible gear. Existing network is base router of RT-AC86U with two remote gig ethernet attached RT-AC68 APs. Thought about upgrading to GT-AX6000 as primary router with two RT-AX86U Pro as APs behind it using a 2.5g switch to connect 2.5g ethernet...
  4. D

    AiMesh not working anymore on 2 latest Merlin firmwares

    Just my experience personally, using 2 AC68U units as APs and an AC86U as the core wifi router, I had nothing but hassles with AI Mesh and 386.x code. I used both ASUS code and Merlin code on AI Mesh nodes and found myself constantly chasing issues which I couldn't resolve. Both nodes were...
  5. D

    Can someone clarify how the WAN DNS order works?

    I'm not certain of the designed intent during normal operation but it appeared, on initial power up, that the router sends out parallel queries at the same time. That behavior might only be during the initialization phase since that was when I was tracing the interface.
  6. D

    HELP! My network is behaving strangely....

    One final note - as someone noted, there are strange things that can happen with AI Mesh configs. In order to clean up some random WiFi weirdness, I deleted my two Merlkin 386.2_6 AP nodes using the AI-Mesh tab on the main router, reset them to factory settings using the WPS method, replaced...
  7. D

    HELP! My network is behaving strangely....

    Closing this out. Stupidly used a -1 address for my static WAN address which proved to be non-responsive. Used a SharkTap between the ComCast gateway and WireShark to validate that the gateway was not responding to the AC86 DNS requests on the wire. Low and behold, when changing the static...
  8. D

    HELP! My network is behaving strangely....

    Still stuck. Static IP fails via AC86 routers running stock and Merlin 386.2_6 but same Comcast interface works with PC connected and static IP addresses. Ordered a ethernet tap adapter to see if I can do packet analysis to determine what's breaking between the AC86 and the Comcast Cisco based...
  9. D

    HELP! My network is behaving strangely....

    Tried changing the DNS to google (8.8.8.8) with no improvement. There is some interaction between static addressing and DNS resolution that I'm just not getting. The user name and password I referred to was for the router itself, not the ISP.
  10. D

    HELP! My network is behaving strangely....

    So, I have an AI Mesh network running 386.2_6 on the core AC86U and 2X AC68U nodes. Last night the network went down for an unknown reason with the core router in a loop cyclically shutting down the radios and the ethernet ports (both WAN and LAN ports) that I couldn't resolve without a serial...
  11. D

    NTP sync fails after reboot randomly

    I'll give it a try Jack - thanks!
  12. D

    NTP sync fails after reboot randomly

    Current WAN DNS servers are prime and secondary Comcast Multicast Servers - could point them toward other servers perhaps. Suggestions? Using a NordVPN client for a single LAN address with a locked-in DNS server within the pipe - don't think that would apply here since it doesn't initialize...
  13. D

    NTP sync fails after reboot randomly

    Still running 384.17 on AC86U for my network router. Having occasional reliability issues with the router failing to time sync after reboot, causing all kinds of havoc. Primary address is pool.ntp.org Just tried adding a hardcoded IP address as a secondary server to a NIST Stratum A destination...
  14. D

    Guest network question

    DNS over TLS is set up on WAN tab with Cloudflare DNS servers as TLS targets. ISP DNS addresses are the default DNS addresses on the same page but I assume go unused because of DoT setting. I'm unclear if the guest networks use the default DNS address or they, too, use the DoT configured addresses.
  15. D

    Guest network question

    Shouldn't need to - it sets ups a SSL tunnel to an upstream host. No inbound packets outside the tunnel that I can see. That's what seems weird about this.
  16. D

    Guest network question

    Only specific limit was blocked access to intranet. Running Skynet but didn't find any outbound blocks on the thermostat's local IP. Does the guest network use the DoT DNS target or the router WAN DNS (they are different - router is using ISP's DNS, DoT is using Cloudflare)?
  17. D

    Guest network question

    What's different with guest networks? Using it to segregate IOT traffic and suddenly a thermostat that was working fine went south. Moved it over to the internal network and everything is hunky dory. Interface gives me little info on the thermo to figure it out. All I was trying to do we limit...
  18. D

    Dumping cfg config files to a readable form

    That met the need - thanks for the suggestion!
  19. D

    Dumping cfg config files to a readable form

    I'm having some weird behavior on my 384.17 AC-86U losing a static IP config in the displayed gui. I've been able to recover using a saved config but realized I have no idea what is actually in the saved config. Has anyone developed a dump utility to convert the config file to an ascii listing...
  20. D

    Release Asuswrt-Merlin 384.19 is now available

    At the risk of provoking folks on this thread that are tired of JFFS issues being discussed, please feel free to pass over this post. After upgrading from .17 to .19 on my AC86U, I had immediate issues with JFFS partition being full and associated weirdness. After deleting traffic analyzer...
Top