What's new
  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

Double NAT trouble? ISP-provided modem/router + GT-AX6000 (w/ RMerlin)

john385

Occasional Visitor
Hi everyone!

Yesterday I was upgraded from a 1Gbps/100Mbps to 2Gbps/100Mbps cable connection.
During the process they (ISP) switched the provided modem/router from Technicolor CGA4236AON to FRITZ!Box 6660 Cable.

While Technicolor worked flawlessy in bridge mode, allowing my GT-AX6000 to fully work as the main router, I'm having insurmountable issues with the Fritzbox 6660. :(

Fritz and ASUS are connected in a way that a cable runs from the Fritz's 2.5G port into ASUS's (2.5G) WAN port.

I've been with the ISP's tech support in-depth yesterday and they assure me that I'm not on CGNAT and that they activated the bridge mode on the Fritz.
I think everything's OK on their end since this is what I'm seeing on the Fritz:

WAN is up and running. The speed is OK:

1.jpg


WAN is not (CG)NAT-ed and does provide a "proper" "outside"ISP's WAN address looking from the Fritz:

2.jpg


Unfortunately, my ASUS shows its WAN IP as the NAT-ed LAN the Fritz assigned it:

4.jpg


I tried various options, nothing works.
The ASUS always sees (gets) the NAT-ed IP address as its WAN IP (192.168.xx.xx).

I set the ASUS to be the "exposed host" on the Fritz.
Enabled Independent Port Sharing.


The problem is that since yesterday:

...I can't see my Plex server from outside the network
...my Wireguard VPN setup (on ASUS) no longer works (can't see any LAN resources from outside LAN).
...port forwarding that worked flawlessy not doesn't work at all.

etc. , etc. the usual Double-NAT issues.

What is to be done here?

Please help me out. :(
 
If the 2.5GbE port can't be used for bridge mode though - it makes this 2Gbps plan useless. 🤷‍♂️
 
1725514249285.png

Asus is only getting IP from Box as shown Gateway: 192.168.178.1. My guess is ISP had not done the correct setting or Box confirmed can't be set to bridge mode. Worst case, Box has to be the main router.

Sorry just a silly confirmation, GT-AX6000 has 2x 2.5Gbps. Is the cable connect to the correct port? If it's connected to LAN then AX6000 will gets 2.5Gbps from Box and will also be getting IP address from Box.
1725515477349.png
 
Last edited:
View attachment 61333
Asus is only getting IP from Box as shown Gateway: 192.168.178.1. My guess is ISP had not done the correct setting or Box confirmed can't be set to bridge mode. Worst case, Box has to be the main router.

Sorry just a silly confirmation, GT-AX6000 has 2x 2.5Gbps. Is the cable connect to the correct port? If it's connected to LAN then AX6000 will gets 2.5Gbps from Box and will also be getting IP address from Box.
View attachment 61335

Fritz is connected to the WAN port on ASUS (same one previously used by Technicolor modem).

I think I’m screwed. :(

I had to go from 1Gpbs to 2Gbps - even though I can’t posssibly use it since I don’t have any 2.5G devices in the house.
They *had* to switch the modem.

Is there a way to configure ASUS in such a way that it works without issues even though there’s a Double NAT going on? 🤔
 
Is there a way to configure ASUS in such a way that it works without issues even though there’s a Double NAT going on? 🤔
Does the FRITZ!Box 6660 support DMZ? If so, as a troubleshooting step, perhaps putting the Asus router into the FRITZ!Box 6660's DMZ may (or maybe not) work.

PS: No idea if the following would apply in your situation.
 

Similar threads

Latest threads

Support SNBForums w/ Amazon

If you'd like to support SNBForums, just use this link and buy anything on Amazon. Thanks!

Sign Up For SNBForums Daily Digest

Get an update of what's new every day delivered to your mailbox. Sign up here!
Back
Top