c152driver
New Around Here
My new RT-AX68U is experiencing fairly regular resets of the wireless interfaces which results in client disconnects for a short period of time. I've seen it on both wl0 and wl1, but primarily wl1.
Over the course of a day this will happen dozens of times.
Corresponding log messages:
Is this likely a hardware issue?
I've tried the following but the problem persists:
Thanks.
Over the course of a day this will happen dozens of times.
Corresponding log messages:
Code:
Aug 26 13:18:40 kernel: wl1: PSM microcode watchdog fired at 7194 (seconds). Resetting.
Aug 26 13:18:40 kernel: wl1: reason = psm watchdog at 7194 seconds. corerev 131 ucode revision 1570.159 features 0x3106
Aug 26 13:18:40 kernel: psmdebug 0x01ff000c phydebug 0x0 macctl 0x4160403 maccmd 0x4
Aug 26 13:18:40 kernel: psm_brc 0x0980 psm_brc_1 0x0200 M_UCODE_DBGST 0x2
Aug 26 13:18:40 kernel: brwk_0 0x05cb brwk_1 0x0014 brwk_2 0x22a0 brwk_3 0x0ff0 brwk_4 0x0006
Aug 26 13:18:40 kernel: ifsstat 0x1ea0 ifsstat1 0xff txectl 0x481c txestat 0x405
Aug 26 13:18:40 kernel: rxestat1 0xa2 rxestat2 0x500 rcv_frmcnt 0x0 rxe_rxcnt 0xe
Aug 26 13:18:40 kernel: wepctl 0x35
Aug 26 13:18:40 kernel: aqmf_ready0 0x0 aqmf_ready1 0x10 aqmf_ready2 0x0 aqmf_ready3 0x0
Aug 26 13:18:40 kernel: aqmf_ready4 0x0 wepstat 0x8000 wep_ivloc 0x10 wep_psdulen 0x8179
Aug 26 13:18:40 kernel: rxe_errval 0x80 rxe_errmask 0x20f rxe_status3 0x20a txe_status2 0x405
Aug 26 13:18:40 kernel: dbg_bmc_status 0x0 psm_chk0_err 0x0 psm_chk1_err 0x0
Aug 26 13:18:40 kernel: PC :
Aug 26 13:18:40 kernel: R0: 0x1860 0x1860 0x1860 0x1860
Aug 26 13:18:40 kernel: psm stack_status : 0x8000
Aug 26 13:18:40 kernel: psm stack_entries:
Aug 26 13:18:40 kernel: 0x1860
Aug 26 13:18:40 kernel: 0x1965
Aug 26 13:18:40 kernel: 0x1ac4
Aug 26 13:18:40 kernel: 0x1ab1
Aug 26 13:18:40 kernel: 0x0f73
Aug 26 13:18:40 kernel: 0x30b5
Aug 26 13:18:40 kernel: 0x1bff
Aug 26 13:18:40 kernel: 0x199a
Aug 26 13:18:40 kernel: wl1: fatal error, reinitializing, total count of reinit's[1]
Is this likely a hardware issue?
I've tried the following but the problem persists:
- Factory reset
- Rolling back to older firmware
- Turning off smart connect
- Disabling auto control channel
- Splitting the bands into separate SSIDs
- Turning off WiFi 6
- Turning off explicit beamforming
Thanks.