Wake On WAN From More Than A Computer Using Script.

daviddrf · Dec 27, 2015

Hello all again. I've been testing the script commented here and it works perfect, thank you!:
https://github.com/RMerl/asuswrt-merlin/wiki/WOL-Script-Wake-Up-Your-Webserver-On-Internet-Traffic
This script allows me to avoid entering on the router's web to wake any computer.
I tested it with one of my two PCs, and it worked flawlessly. I've been using the search engine of this forum but I haven't been able to find the answer to the following two questions:

1) How should I do for being able to wake more than a computer using the script named before?
2) Is there any way to Wake On WAN in AsusWRT-Merlin like it is done in DD-WRT without scripts, with telnet commands making a permanent ARP table entry like "arp -i br0 -s 192.168.x.x XX:XX:XX:XX:XX:XX"? (like this: http://www.ptere.com/wol/)

Thanks in advance.

Steffe · Dec 28, 2015

1) Both at the same time or independently? First option; add another "$WOL -i $IFACE $MAC"... Second option requires that you run two scripts(or one if you rewrite the code) which monitors different ports for traffic.

2) You can only make Wake on Wan if you add entries. These will reset upon router reboot. I've made a script to add them post boot. So, i guess that is a no to your answer..

faria · Dec 28, 2015

I just duplicate the script from the wiki ( one entry per device) into a single script.

daviddrf · Dec 28, 2015

Hello again. First of all thank you Steffe and faria por your answers and support.

Steffe said:
1) Both at the same time or independently? First option; add another "$WOL -i $IFACE $MAC"... Second option requires that you run two scripts(or one if you rewrite the code) which monitors different ports for traffic.

2) You can only make Wake on Wan if you add entries. These will reset upon router reboot. I've made a script to add them post boot. So, i guess that is a no to your answer..

1) I would like to to it independently. How could I do that in only one script rewriting the code? I already did the port forwarding/redirection for each port for either PC.

2) A script to autoadd the static ARP table's entries post boot would be great. Is this not the same than the script said before?

faria said:
I just duplicate the script from the wiki ( one entry per device) into a single script.

How would "look" this final single script?

Thank you again Steffe and faria for your support.

faria · Dec 29, 2015

As Such:

Code:

#!/bin/sh
/usr/bin/logger -t START_$(basename $0) "started [$@]"
INTERVAL=5
NUMP=3
OLD=""
TARGET=192.168.1.236 #SKYNET
PORT=3390
IFACE=br0
MAC=XX:04:A6:4A:C0:XX
WOL=/usr/bin/ether-wake
LOGFILE="/var/log/ether-wake.log"

while sleep $INTERVAL;do
NEW=`dmesg | awk '/ACCEPT/ && /DST='"$TARGET"'/ && /DPT='"$PORT"'/ {print }' | tail -1`
SRC=`echo $NEW | awk -F'[=| ]' '{print $8}'`
DPORT=`echo $NEW | awk -F'[=| ]' '{print $27}'`
PROTO=`echo $NEW | awk -F'[=| ]' '{print $23}'`

if [ "$NEW" != "" -a "$NEW" != "$OLD" ]; then
if ! ping -qc $NUMP $TARGET >/dev/null; then
# echo "NOWAKE $TARGET was accessed by $SRC, port $DPORT, protocol $PROTO and is already alive at" `date`>> $LOGFILE
# else
echo "WAKE $TARGET requested by $SRC, port $DPORT, protocol $PROTO at" `date`>> $LOGFILE
$WOL -i $IFACE $MAC
sleep 5
fi
OLD=$NEW
fi
done

#######################################################
INTERVAL=5
NUMP=3
OLD=""
TARGET=192.168.1.200# NAS
PORT=
IFACE=br0
MAC=XX:11:32:2D:13:XX
WOL=/usr/bin/ether-wake
LOGFILE="/var/log/wakenas.log"

while sleep $INTERVAL;do
NEW=`dmesg | awk '/ACCEPT/ && /DST='"$TARGET"'/ && /DPT='"$PORT"'/ {print }' | tail -1`
SRC=`echo $NEW | awk -F'[=| ]' '{print $8}'`
DPORT=`echo $NEW | awk -F'[=| ]' '{print $27}'`
PROTO=`echo $NEW | awk -F'[=| ]' '{print $23}'`

if [ "$NEW" != "" -a "$NEW" != "$OLD" ]; then
if ! ping -qc $NUMP $TARGET >/dev/null; then
# echo "NOWAKE $TARGET was accessed by $SRC, port $DPORT, protocol $PROTO and is already alive at" `date`>> $LOGFILE
# else
echo "WAKE $TARGET requested by $SRC, port $DPORT, protocol $PROTO at" `date`>> $LOGFILE
$WOL -i $IFACE $MAC
sleep 5
fi
OLD=$NEW
fi
done
####################################################
INTERVAL=5
NUMP=3
OLD=""
TARGET=192.168.1.111 #Patricia pc
PORT=3388
IFACE=br0
MAC=XX:46:5D:89:EC:XX
WOL=/usr/bin/ether-wake
LOGFILE="/var/log/ether-wakejunkyard.log"

while sleep $INTERVAL;do
NEW=`dmesg | awk '/ACCEPT/ && /DST='"$TARGET"'/ && /DPT='"$PORT"'/ {print }' | tail -1`
SRC=`echo $NEW | awk -F'[=| ]' '{print $8}'`
DPORT=`echo $NEW | awk -F'[=| ]' '{print $27}'`
PROTO=`echo $NEW | awk -F'[=| ]' '{print $23}'`

if [ "$NEW" != "" -a "$NEW" != "$OLD" ]; then
if ! ping -qc $NUMP $TARGET >/dev/null; then
# echo "NOWAKE $TARGET was accessed by $SRC, port $DPORT, protocol $PROTO and is already alive at" `date`>> $LOGFILE
# else
echo "WAKE $TARGET requested by $SRC, port $DPORT, protocol $PROTO at" `date`>> $LOGFILE
$WOL -i $IFACE $MAC
sleep 5
fi
OLD=$NEW
fi
done
/usr/bin/logger -t STOP_$(basename $0) "return code $?"

daviddrf · Dec 29, 2015

faria said:

As Such:

Code:

#!/bin/sh
/usr/bin/logger -t START_$(basename $0) "started [$@]"
INTERVAL=5
NUMP=3
OLD=""
TARGET=192.168.1.236 #SKYNET
PORT=3390
IFACE=br0
MAC=XX:04:A6:4A:C0:XX
WOL=/usr/bin/ether-wake
LOGFILE="/var/log/ether-wake.log"

while sleep $INTERVAL;do
NEW=`dmesg | awk '/ACCEPT/ && /DST='"$TARGET"'/ && /DPT='"$PORT"'/ {print }' | tail -1`
SRC=`echo $NEW | awk -F'[=| ]' '{print $8}'`
DPORT=`echo $NEW | awk -F'[=| ]' '{print $27}'`
PROTO=`echo $NEW | awk -F'[=| ]' '{print $23}'`

if [ "$NEW" != "" -a "$NEW" != "$OLD" ]; then
if ! ping -qc $NUMP $TARGET >/dev/null; then
# echo "NOWAKE $TARGET was accessed by $SRC, port $DPORT, protocol $PROTO and is already alive at" `date`>> $LOGFILE
# else
echo "WAKE $TARGET requested by $SRC, port $DPORT, protocol $PROTO at" `date`>> $LOGFILE
$WOL -i $IFACE $MAC
sleep 5
fi
OLD=$NEW
fi
done

#######################################################
INTERVAL=5
NUMP=3
OLD=""
TARGET=192.168.1.200# NAS
PORT=
IFACE=br0
MAC=XX:11:32:2D:13:XX
WOL=/usr/bin/ether-wake
LOGFILE="/var/log/wakenas.log"

while sleep $INTERVAL;do
NEW=`dmesg | awk '/ACCEPT/ && /DST='"$TARGET"'/ && /DPT='"$PORT"'/ {print }' | tail -1`
SRC=`echo $NEW | awk -F'[=| ]' '{print $8}'`
DPORT=`echo $NEW | awk -F'[=| ]' '{print $27}'`
PROTO=`echo $NEW | awk -F'[=| ]' '{print $23}'`

if [ "$NEW" != "" -a "$NEW" != "$OLD" ]; then
if ! ping -qc $NUMP $TARGET >/dev/null; then
# echo "NOWAKE $TARGET was accessed by $SRC, port $DPORT, protocol $PROTO and is already alive at" `date`>> $LOGFILE
# else
echo "WAKE $TARGET requested by $SRC, port $DPORT, protocol $PROTO at" `date`>> $LOGFILE
$WOL -i $IFACE $MAC
sleep 5
fi
OLD=$NEW
fi
done
####################################################
INTERVAL=5
NUMP=3
OLD=""
TARGET=192.168.1.111 #Patricia pc
PORT=3388
IFACE=br0
MAC=XX:46:5D:89:EC:XX
WOL=/usr/bin/ether-wake
LOGFILE="/var/log/ether-wakejunkyard.log"

while sleep $INTERVAL;do
NEW=`dmesg | awk '/ACCEPT/ && /DST='"$TARGET"'/ && /DPT='"$PORT"'/ {print }' | tail -1`
SRC=`echo $NEW | awk -F'[=| ]' '{print $8}'`
DPORT=`echo $NEW | awk -F'[=| ]' '{print $27}'`
PROTO=`echo $NEW | awk -F'[=| ]' '{print $23}'`

if [ "$NEW" != "" -a "$NEW" != "$OLD" ]; then
if ! ping -qc $NUMP $TARGET >/dev/null; then
# echo "NOWAKE $TARGET was accessed by $SRC, port $DPORT, protocol $PROTO and is already alive at" `date`>> $LOGFILE
# else
echo "WAKE $TARGET requested by $SRC, port $DPORT, protocol $PROTO at" `date`>> $LOGFILE
$WOL -i $IFACE $MAC
sleep 5
fi
OLD=$NEW
fi
done
/usr/bin/logger -t STOP_$(basename $0) "return code $?"

Thank you a lot faria for sharing this script. With this script it would be possible to wake 3 different computers, right?

faria · Dec 30, 2015

daviddrf said:
Thank you a lot faria for sharing this script. With this script it would be possible to wake 3 different computers, right?

Yes, been using it for over a year.
You can add more devices if you wish.
Remember :
You also need to add the mac a dresses to the wake on lan router page.
You also need to foward the ports used in the script.
If you use a vpn client you also need to foward the ports using a selective routing script.
And finally, you need to configure your devices wake on lan features on,bios,network cards and operation system if needed.
Windows 8 and 10 can be triky because of fast startup,you may have to desable it in windows.
Once properly configured you can launch remote desktop from another device once you press connect it will start up the pc you trying to reach and login. Please note that the delay starting up the pc may timeout the remote desktop session in that case press connect once again.
Example:
You know that you pc takes 60 seconds to boot from cold,
When you press connect in the temote desktop app it will send a magic packet and will wake the pc, but because the boot process Is quite long the remote desktop app will time out.
By waiting 1 minute after first ping you are making sure the pc is up and running, now pressing connect in the remote desktop app it will log you in.

daviddrf · Dec 30, 2015

faria said:
Yes, been using it for over a year.
You can add more devices if you wish.
Remember :
You also need to add the mac a dresses to the wake on lan router page.
You also need to foward the ports used in the script.
If you use a vpn client you also need to foward the ports using a selective routing script.
And finally, you need to configure your devices wake on lan features on,bios,network cards and operation system if needed.
Windows 8 and 10 can be triky because of fast startup,you may have to desable it in windows.
Once properly configured you can launch remote desktop from another device once you press connect it will start up the pc you trying to reach and login. Please note that the delay starting up the pc may timeout the remote desktop session in that case press connect once again.
Example:
You know that you pc takes 60 seconds to boot from cold,
When you press connect in the temote desktop app it will send a magic packet and will wake the pc, but because the boot process Is quite long the remote desktop app will time out.
By waiting 1 minute after first ping you are making sure the pc is up and running, now pressing connect in the remote desktop app it will log you in.

Yes, I sucessfully tested it today, thank you again faria.
I noticed that sometimes there's a delay (some seconds) between the momment when I send the magic packet and the PC wakes on. Is this something related to the script?

faria · Dec 31, 2015

daviddrf said:
Yes, I sucessfully tested it today, thank you again faria.
I noticed that sometimes there's a delay (some seconds) between the momment when I send the magic packet and the PC wakes on. Is this something related to the script?

It is and it's not,I asume that the script itself I not the problem but the time the router takes to check the script,find the target device and then send the packet to wake it.
It's quite allot going on in the background to wake a device in this maner.
Perhaps someone with more knowledge about it can chime in.

daviddrf · Dec 31, 2015

faria said:
It is and it's not,I asume that the script itself I not the problem but the time the router takes to check the script,find the target device and then send the packet to wake it.
It's quite allot going on in the background to wake a device in this maner.
Perhaps someone with more knowledge about it can chime in.

I understand. It's OK, thank you again faria for your support and happy new year

.

daviddrf · Aug 28, 2016

Hello. First of all I want to say sorry for reviving an almost nine month old post.
I want only to say that I've found a better way to enable Wake On WAN (LAN and outside from LAN) on my RT-AC68U with AsusWRT-Merlin firmware than the proposed by faria. I had tested this way on my older routers with DD-WRT, and in all of them worked like a charm. This way consists in enabling a PERMANENT static entry (which stays and remains in the ARP table even after rebooting the router) connecting the private LAN IP to the ethernet card MAC address you want to wake up.
The faria way was cool, the problem is I wasn't able to wake up any device after some hours. I was able to wake up in the first hours since last reboot, but later was imposible. Then I have been looking for this forum and I found this very useful post: http://www.snbforums.com/threads/create-static-arp-using-services-start-to-survive-reboot.34100/
This was EXACTLY was I was looking for. With this way you apply that permanent static entry in the ARP table in the "services-start" file which exists after enabling the JFFS partition and its configs and scripts under the "Administration tab". You can even access it with WINSCP like it is shown in this tutorial and manually editing the "services-start" file:
https://github.com/RMerl/asuswrt-merlin/wiki/WOL-Script-Wake-Up-Your-Webserver-On-Internet-Traffic
Although is much faster "writing" it on the router by telnet or SSH access like on the first post is said:

Code:

cat << EOF > /jffs/scripts/services-start
#!/bin/sh
/sbin/arp -s 192.168.1.2 AB:CD:EF:1G:2F:3G
EOF

Then...

Code:

chmod 777 /jffs/scripts/services-start

...and finally...

Code:

reboot

After rebooting the router I've tested it on it and I am able to quickly wake any device forever, a lot of hours after the router was rebooted. In addition the faria way has a little bit delay between you hit the WAKE UP button and the computer wakes UP. This other way is INMEDIATE, there's no delay.
Thank you all and goodbye

.

chiquito · Oct 1, 2016

I have done everything poneis in the scripts but in the last operation where it says go and accept packages firewall and router to reboot I run out of internet pages do not open

MKANET · Jul 4, 2017

David, thanks so much for your post. Just over 40 minutes ago I realized my Asus RT-AC5300's stock firmware didn't have a way to save or run the ARP -s command I needed for WOL (after my router reboots). I was able to find your post, which showed EXACTLY how to do this step-by-step; even, with very little Linux experience.

daviddrf said:
Hello. First of all I want to say sorry for reviving an almost nine month old post.
I want only to say that I've found a better way to enable Wake On WAN (LAN and outside from LAN) on my RT-AC68U with AsusWRT-Merlin firmware than the proposed by faria. I had tested this way on my older routers with DD-WRT, and in all of them worked like a charm. This way consists in enabling a PERMANENT static entry (which stays and remains in the ARP table even after rebooting the router) connecting the private LAN IP to the ethernet card MAC address you want to wake up.
The faria way was cool, the problem is I wasn't able to wake up any device after some hours. I was able to wake up in the first hours since last reboot, but later was imposible. Then I have been looking for this forum and I found this very useful post: http://www.snbforums.com/threads/create-static-arp-using-services-start-to-survive-reboot.34100/
This was EXACTLY was I was looking for. With this way you apply that permanent static entry in the ARP table in the "services-start" file which exists after enabling the JFFS partition and its configs and scripts under the "Administration tab". You can even access it with WINSCP like it is shown in this tutorial and manually editing the "services-start" file:
https://github.com/RMerl/asuswrt-merlin/wiki/WOL-Script-Wake-Up-Your-Webserver-On-Internet-Traffic
Although is much faster "writing" it on the router by telnet or SSH access like on the first post is said:

Code:

cat << EOF > /jffs/scripts/services-start #!/bin/sh /sbin/arp -s 192.168.1.2 AB:CD:EF:1G:2F:3G EOF

Then...

Code:

chmod 777 /jffs/scripts/services-start

...and finally...

Code:

reboot

After rebooting the router I've tested it on it and I am able to quickly wake any device forever, a lot of hours after the router was rebooted. In addition the faria way has a little bit delay between you hit the WAKE UP button and the computer wakes UP. This other way is INMEDIATE, there's no delay.
Thank you all and goodbye .[/CODE]

elorimer · Jul 4, 2017

Is there a way this works within the LAN? I.e., if I RDP from one computer to another in the same LAN?

faria · Jul 4, 2017

elorimer said:
Is there a way this works within the LAN? I.e., if I RDP from one computer to another in the same LAN?

Yes , but you will have to use a different port number in the second Pc,
Also once you change the Port number on the second pc you need to forward the port on the router .
And finally once you changed the RDP port on the second pc , you need to create a firewall exception for the new port on the Windows firewall .

chiquito · Aug 7, 2019

I have an rt-ac88u router with merlin firmware and I often use wake on lan on my pc to control it from outside my network.
The problem is that when the router is reset it loses the entry in the router's arp table, I created the scripts that you put in the forum but it doesn't work for me when I reset the route the ip changes and I have to put the arp data back by hand..
You know why I created the services-start file inside the jffs / scripts / folder, I have given it 0777 permissions and it doesn't work for me, any ideas?
Thank you ..

daviddrf · Aug 7, 2019

chiquito said:
I have an rt-ac88u router with merlin firmware and I often use wake on lan on my pc to control it from outside my network.
The problem is that when the router is reset it loses the entry in the router's arp table, I created the scripts that you put in the forum but it doesn't work for me when I reset the route the ip changes and I have to put the arp data back by hand..
You know why I created the services-start file inside the jffs / scripts / folder, I have given it 0777 permissions and it doesn't work for me, any ideas?
Thank you ..

Hello. I'm sure that this happens because you make some mistake in the procedure which is described in this post.

chiquito · Aug 7, 2019

I have done it as described in the jjfs post format then I paste the lines in the services-start file I give permissions 0777 and reboot and I still change the ip

Enviado desde mi iPhone utilizando Tapatalk

ColinTaylor · Aug 7, 2019

chiquito said:
... when I reset the route the ip changes ...

Sorry I don't understand what you're saying. What are you resetting?

chiquito · Aug 7, 2019

The scripts described in the post is not so that when the router restarts the ip does not change?

Thread starter	Title	Forum	Replies	Date
	Auto Wake On Lan?	Asuswrt-Merlin	24	Apr 27, 2024
M	I lose connection every few days in the mornings. No internet when we wake up.	Asuswrt-Merlin	6	Mar 12, 2024
S	Solved New ISP - WAN Setup - Will not work with custom WAN DNS - dnsmasq.conf	Asuswrt-Merlin	1	Nov 5, 2024
Z	Dual WAN + Dual Firewall	Asuswrt-Merlin	11	Nov 4, 2024
M	RT-AX86U Pro - Merlin: can't get p2p cameras available to wan.	Asuswrt-Merlin	4	Nov 4, 2024
	RT-BE88U and Dynamic WAN Port MAC?	Asuswrt-Merlin	0	Oct 30, 2024
M	802.1q VLAN tagging menu missing for WAN interface (Asus RT-AX86U Pro)	Asuswrt-Merlin	4	Oct 30, 2024
U	How to switch secondary WAN to Hot-Standby?	Asuswrt-Merlin	2	Oct 29, 2024
	Dual WAN IPv6	Asuswrt-Merlin	2	Oct 8, 2024
	Switch WAN type from SSH	Asuswrt-Merlin	3	Sep 25, 2024

Wake On WAN From More Than A Computer Using Script.

Occasional Visitor

Regular Contributor

Senior Member

Occasional Visitor

Senior Member

Occasional Visitor

Senior Member

Occasional Visitor

Senior Member

Occasional Visitor

Occasional Visitor

Occasional Visitor

Regular Contributor

Part of the Furniture

Senior Member

Occasional Visitor

Occasional Visitor

Occasional Visitor

Part of the Furniture

Occasional Visitor

Similar threads

Similar threads

Support SNBForums w/ Amazon

Sign Up For SNBForums Daily Digest