Menu
What's new
By:
Filters Better Search

Search results

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

  1. iotzan

    Asuswrt-Merlin 3.0.0.4.374.38 is out

    Hi Merlin, First of all, thank you for your work. PPPoE performance is back up. As far as the WiFi tests go, I don't see any performance degradation or any improvements whatsoever. Then again we're talking about a 1 floor, 85 sqm space so I'm not sure if it counts. 2.4 Ghz is stable at 72...
  2. iotzan

    Looking for feedback: PPPoE and poor WAN performance

    I am currently using 3.0.0.4.374.36_beta1-sdk5 and I tried 3.0.0.4.374.36_beta1 too. At most I get 170 Mbps. I am 95% sure that scorpionro and I share the same provider.
  3. iotzan

    Just bought Asus RT-AC66U

    You should use the latest firmware if your down speed is lower than 170 Mbps.
  4. iotzan

    Feedback: any Dual WAN user?

    Currently on RT-N66U_3.0.0.4_374.36_beta1-sdk5. Configured for Fail Over, the N66U router will not switch back to the primary link. I don't see a way to trigger it other than rebooting the router or toggling the Dual Wan Off/On. The load balancing is also pretty sketchy. The ratio doesn't seem...
  5. iotzan

    Looking for feedback: PPPoE and poor WAN performance

    Hello Merlin, Writing here for posterity as I had already made a thread for this issue. My connection is a GPON FTTB to "black box", then Ethernet [1 Gbps down / 100 Mbps up] to an Asus RT-N66U router. Going back through all of your firmware revisions, the most recent version that provides me...
  6. iotzan

    pppoe speed issue

    Thanks for your reply Merlin. I too am one of the, hopefully few, ones affected by the lack of HW acceleration for PPPoE. While 3.0.0.4.354.29 is fine for now, I am sorely missing the dual WAN capabilities. Do you have any hopes of getting this into a new FW?
  7. iotzan

    RT-N66U PPPoE low throughput

    I guess that I somewhat resolved the issue with RT-N66U_3.0.0.4_354.29-BETA1. After changing some more firmwares, I got back to it and after a reboot I'm getting 85MB/s down, 14MB/s up. I guess this will have to do, though I am not sure what I can do about the missing dual WAN in this release.
  8. iotzan

    RT-N66U PPPoE low throughput

    I've also installed RT-N66U_3.0.0.4_354.29-BETA1 which brings me up to 47 MB/s down, 4.5 MB/s up. A little bit better. Any further recommendations to improve my speeds?
  9. iotzan

    RT-N66U PPPoE low throughput

    Hello! I've just got a 1 GBps line installed and the RT-N66U is falling short of expectations. I've updated to both RT-N66U_3.0.0.4_374.35_4 and RT-N66U_3.0.0.4_374.35_4-sdk5 (current), but I am getting, at most, 23 MB/s down, 3 MB/s up. I'm not expecting max speeds, but even the laptop...
  10. iotzan

    (Static IP) WAN issue, little to no throughput

    I would try to change the MTU, but I can't seem to find it in RT-N66Us settings.
  11. iotzan

    (Static IP) WAN issue, little to no throughput

    I'm sorry, I don't follow. My ISP provides a Cat5e. I can use that either directly or put a router in between. I only have problems when I'm using the router. It works perfectly when using the link directly or through a switch. I was previously using a D-Link DIR-600 and had no issues.
  12. iotzan

    (Static IP) WAN issue, little to no throughput

    No. If I reset to original settings and go through the set up again, from my PC or laptop exclusively, the same issue manifests. EDIT: I have tried a lot of different configuration options. I am reluctant to post them so as to not focus anyone on a potential wrong issue. I am however, open to...
  13. iotzan

    (Static IP) WAN issue, little to no throughput

    I have tried with the 2 GWs listed in my test results and also with Google's DNS servers in addition to the 3 DNS servers of my ISP. I did read something around here, which I also tried. I set my router, 192.168.1.1 as DNS server in the LAN - DHCP server page. This results in getting some...
  14. iotzan

    (Static IP) WAN issue, little to no throughput

    Hello everyone, I've been trying to get my new router to work for almost a week now. Being out of options, I thought I might bother you for some help. The router came with firmware 3.0.0.4.260. My WAN is set up as Static IP with 2 ISP-provided DNS servers entered manually. I also provide...
Top