What's new

Entware after reboot

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

I have kind of the same problems. Transmission and minidlna won't start automaticly after reboot.
Fresh install of entware , no optware installed previously.
jffs scripts have been chmod and haven't changed anything to them beside adding swapon/swapoff.
If i start services-start manually after boot via putty, everything starts properly.
Any clue?
 
Hi, i have the same problem, i update my rt-n66 from 376.47 Merlin fw to 378.51 and with the latest firmware after every reboot can't found entware folder, i tried to format usb, downgrade and upgrade Merlin firmware but not work. Now i restore the 376.47 version and all work fine.
 
I have kind of the same problems. Transmission and minidlna won't start automaticly after reboot.
Hi, i have the same problem, i update my rt-n66 from 376.47 Merlin fw to 378.51 and with the latest firmware after every reboot can't found entware folder, i tried to format usb, downgrade and upgrade Merlin firmware but not work. Now i restore the 376.47 version and all work fine.
Hi,

After updating to .51 version I found out that the USB-Mount does not happen always at the same time.
Did you put the Entware start into the post-mount script? This will ensure that your Entware startup will happen after the USB drive is avaliable...:rolleyes:

Here my post-mount script with the Entware start (in red) - do not forget to change the if command with the right mount-point of your USB drive(!):
#!/bin/sh
/usr/bin/logger -t START_$(basename $0) "started [$@]"
SCRLOG=/tmp/$(basename $0).log
touch $SCRLOG
echo "START_$(basename $0) started [$@]" >> $SCRLOG

#
if [ $1 = "/tmp/mnt/sdcard" ] # change the mount-point to your USB-drive!
then
mkdir /tmp/opt >> $SCRLOG
/bin/mount -o bind /tmp/mnt/sdcard/Optware /opt >> $SCRLOG
/opt/etc/init.d/rc.unslung start >> $SCRLOG
wait

fi
#
if [ "$?" -ne 0 ]
then
echo "Error in postmount execution! Script: $0" >> $SCRLOG
else
echo "Postmount execution OK. Script: $0" >> $SCRLOG
fi

/usr/bin/logger -t STOP_$(basename $0) "return code $?"
exit $?

By the way the commands in blue will create a nice post-mount.log file in the /tmp folder for analyzing afterwards what happened during boot time! ;)

With kind regards
Joe :cool:
 
Last edited:
Hi,

After updating to .51 version I found out that the USB-Mount does not happen always at the same time.
Did you put the Entware start into the post-mount script? This will ensure that your Entware startup will happen after the USB drive is avaliable...:rolleyes:

Here my post-mount script with the Entware start (in red) - do not forget to change the if command with the right mount-point of your USB drive(!):


By the way the commands in blue will create a nice post-mount.log file in the /tmp folder for analyzing afterwards what happened during boot time! ;)

With kind regards
Joe :cool:

Hi joegreat, thank you for your reply. No, i don't put the start command into the post mont script. Tomorrow i will try to reinstall latest firmware and write the command into the script.

Thanks a lot for your advice
Dani
 
Have problems with entware too on n66u.
Install entware with script, opkg install mc and run wan-start script(its updates ip addres via yandex api). Everything works as usual...until reboot. So after reboot i see that jffs and /dev/sda (internal sd card) filesystem persist, but no opkg or mc commands are known. After reinstalling entware i see backup of old entware installation named "entware-old_2015-04-21_21-25".

Using 3.0.0.4.378.51_0
 
I had the problem as well on my ASUSWRT-MERLIN version 378.53@RT87U, no opkg command after reboot.
After some searching, I found out the problem was caused by the symbolic link in /tmp/opt. The original symbolic link was "opt -> /tmp/mnt/1.41.12-3255/asusware.arm/", and should be "opt -> /tmp/mnt/1.41.12-3255/entware.arm/"
And then I found out the problem is that the command "ln -sf $1/entware.arm /tmp/opt" in the path "/jffs/scripts/post-mount" isnt working.
I dont know why, but when I changed the command to "ln -nsf $1/entware.arm /tmp/opt" things come to work now.
 
I had the problem as well on my ASUSWRT-MERLIN version 378.53@RT87U, no opkg command after reboot.
After some searching, I found out the problem was caused by the symbolic link in /tmp/opt. The original symbolic link was "opt -> /tmp/mnt/1.41.12-3255/asusware.arm/", and should be "opt -> /tmp/mnt/1.41.12-3255/entware.arm/"
And then I found out the problem is that the command "ln -sf $1/entware.arm /tmp/opt" in the path "/jffs/scripts/post-mount" isnt working.
I dont know why, but when I changed the command to "ln -nsf $1/entware.arm /tmp/opt" things come to work now.

That fixed my problem. Manually linked it and all was good.
 

Support SNBForums w/ Amazon

If you'd like to support SNBForums, just use this link and buy anything on Amazon. Thanks!

Sign Up For SNBForums Daily Digest

Get an update of what's new every day delivered to your mailbox. Sign up here!
Top