Intermittent loss of Wi-Fi since upgrading to 386.7
- Thread starter TheLyppardMan
- Start date
belleDESiRE
Occasional Visitor
I have the same issue on my ax88u since 386.7.
wifi disconnects, followed by a log spam (until reboot) with the wlc_send_bar, wlc_ampdu_recv_addba_resp failed and wlc_recvfilter bad frame control and other errors
Moved all my google nest devices to 2.4ghz (I have a different ssid for 2.4 and 5ghz), that did make the frequency of the crashes less often.
Then a few days later reset the "Group Key Rotation Interval" back to the default of 3600 (had it set to 8 hours before since years), and now it is actually happening a lot more than before.
Just set it to '0' for both 2.4 ang 5ghz, lets see if this at least makes it again less frequent. Obviously this has some security concerns.
Let's see, hope a new FW version comes soon
wifi disconnects, followed by a log spam (until reboot) with the wlc_send_bar, wlc_ampdu_recv_addba_resp failed and wlc_recvfilter bad frame control and other errors
Moved all my google nest devices to 2.4ghz (I have a different ssid for 2.4 and 5ghz), that did make the frequency of the crashes less often.
Then a few days later reset the "Group Key Rotation Interval" back to the default of 3600 (had it set to 8 hours before since years), and now it is actually happening a lot more than before.
Just set it to '0' for both 2.4 ang 5ghz, lets see if this at least makes it again less frequent. Obviously this has some security concerns.
Let's see, hope a new FW version comes soon
Last edited:
belleDESiRE
Occasional Visitor
Ok, crash again. so Group Key Rotation Interval back to 3600 and going to dirty downgrade to 386.5_2 now 
Last edited:
ec.auction
New Around Here
Morpheus2020
Regular Contributor
You replied to me here.
Release - Asuswrt-Merlin 386.7 is now available for all models
Flashed on GT-AXE11000, VPN does NOT work with Nord. Same setup in stock works perfectly. On this build it is not working. I get the green light showing its engaged bit when I go to a site that will only work through a VPN it says I do not have a VPN running. Flashed back to the stock, same site...
www.snbforums.com
In 386.5.2, 5G WiFi can work at 160MHz all the time, if I set 5G bandwidth to 160MHz.
Still no problem to report since 21 days with the 386.7 Firmware.
As I said before, I don't activate the 160 Mhz case for the 5 Ghz Wifi.
I leave this default setting on AUTO and so my wifi devices connect in 80 Mhz like on the screenshot of Makaveli.
However, I am very satisfied with the speed, even with several devices connected at the same time.
In any case I am very happy with this firmware which has not given me any problems so far.
For some people who have disconnection problems when activating the 160 Mhz, I think it will be necessary to wait for the 386.7_2 version.
As I said before, I don't activate the 160 Mhz case for the 5 Ghz Wifi.
I leave this default setting on AUTO and so my wifi devices connect in 80 Mhz like on the screenshot of Makaveli.
However, I am very satisfied with the speed, even with several devices connected at the same time.
In any case I am very happy with this firmware which has not given me any problems so far.
For some people who have disconnection problems when activating the 160 Mhz, I think it will be necessary to wait for the 386.7_2 version.
Last edited:
Makaveli
Very Senior Member
You replied to me here.
But look at the picture you posted in this thread. Channel is 36/80. This means your router's 5G WiFi is also reduced to 80MHz when no 160MHz device is connected. This is what I call the 160MHz bug in 386.7.Release - Asuswrt-Merlin 386.7 is now available for all models
Flashed on GT-AXE11000, VPN does NOT work with Nord. Same setup in stock works perfectly. On this build it is not working. I get the green light showing its engaged bit when I go to a site that will only work through a VPN it says I do not have a VPN running. Flashed back to the stock, same site...
In 386.5.2, 5G WiFi can work at 160MHz all the time, if I set 5G bandwidth to 160MHz.
no that post you are quoting is days older than the last one.
In that post I didn't have 160Mhz enabled.
In the follow up post I did. I don't normally use 160mhz but I enabled it to test after I saw your post.
Last edited:
Treadler
Very Senior Member
I don’t use 160 mhz, but 386.7 (after 3 - 4 days) settled in with intermittent wifi disconnects.
As previously noted, I did a full reset, & reintroduced scripts I was running one at a time.
Go figure…..
Treadler
Very Senior Member
I have no doubt the wizard will be all over this!
eibgrad
Part of the Furniture
Seems to me if the vast majority of those having issues w/ 386.7 are NOT having them w/ 386.5_2, then it makes no sense to continue w/ 386.7.
In my experience, far too many ppl upgrade just for the sake of remaining current. Unless the new firmware addresses serious vulnerabilities or bugs that directly affect you, you should STOP chasing upgrades just because they are available. You need to appreciate the value of stable existing firmware before delving into the unknown of new firmware, esp. if its only known benefit is that it's NEW!
As far as I can tell, there's simply no compelling reason to embrace 386.7 that warrants all this trouble. Esp. if 388.x supposedly offers some relief.
In my experience, far too many ppl upgrade just for the sake of remaining current. Unless the new firmware addresses serious vulnerabilities or bugs that directly affect you, you should STOP chasing upgrades just because they are available. You need to appreciate the value of stable existing firmware before delving into the unknown of new firmware, esp. if its only known benefit is that it's NEW!
As far as I can tell, there's simply no compelling reason to embrace 386.7 that warrants all this trouble. Esp. if 388.x supposedly offers some relief.
You are absolutely right. However, is it possible to keep the 386.7 version for now (which works perfectly for me) and not update the following versions (386.7_1, 386.7_2...) and only flash the 388 version when it will be released ?
This one will completely overwrite the 386.7 ? (provided you do a WPS reset after the 388 update to get the default settings of course)
brummygit
Very Senior Member
I've also had WiFi issues on my network since upgrading to 386.7 however I am in what I suspect is a lucky position that my main router is an RT-AX88U with 2 x RT-AX86U ethernet backhaul AiMesh nodes which carry most of the traffic. I have upgraded both nodes to stock 3.0.0.4.386_49599, removed and re-added them to reset their configs, and my network is performing very well now. I think my Ring Cameras etc are the best I have ever known.
I know this won't be an option for many, however I wanted to provide some confidence that Asus appear to have a fix in the newer drivers and therefore RMerlin will almost certainly roll out this new code in due course.
I know this won't be an option for many, however I wanted to provide some confidence that Asus appear to have a fix in the newer drivers and therefore RMerlin will almost certainly roll out this new code in due course.
TheLyppardMan
Very Senior Member
I've never used the 160 MHz settings, but I still get the Wi-Fi dropouts, so it's not just limited to use of 160 MHz where the problems are occurring.
I've had major issues with my shield TV connecting since the upgrade. When forced to 5GHz it often wouldn't connect for 5 minutes (if at all) after a cold boot. Seemed to be a bit better after allowing it to use 2.4, but still not perfect.
It coincided with an OS update, so could just be a red herring mind you. I've rolled back to 386.5_2 and will have a play with it later to see if there's any improvement.
No issues aside from that, though.
/edit
Yeah, seems fine now after going back to 386.5_2 and forcing the Shield to use 5GHz only again.
It coincided with an OS update, so could just be a red herring mind you. I've rolled back to 386.5_2 and will have a play with it later to see if there's any improvement.
No issues aside from that, though.
/edit
Yeah, seems fine now after going back to 386.5_2 and forcing the Shield to use 5GHz only again.
Last edited:
388 wont come for months, possibly not until next year for existing models.
I received an updated driver/SDK for the RT-AX86U, I haven't had time to test it yet.
As for the RT-AX88U, a new GPL is expected in the coming weeks to add support for a new SoC revision.
splendid_koi
Occasional Visitor
Same issues here on my GT-AX11000 on 386.7 (dirty flash from 386.5_2). I thought at first it was my piHole but finally realized that the radio itself reboots, doesn't seem to be the whole router. Most of the time it's the 5GHZ-2 which I have set to AX Only with 160 MHz enabled and I use that for my work laptops. I do know the other bands reboot as well because I have about 50 devices on the 2.4GHZ band and I often see notifications that multiple devices have lost connection recently. Once we are done working today I will redo a clean install to 386.5_0 and go from there.
Do you foresee having enough time to: Stuff the updated driver/SDK for the RT-AX86U into 386.7_2 ???
I'd love to retest 160MHz with the new drivers, as Tech9 seems to be having much improved WiFi since going stock.
Myself I can't easily go stock because I'll loose my USB-drive functionality & it's tied to my DIY home automation.
Last edited:
Similar threads
Similar threads
Similar threads
-
Intermittent problem with DHCP offering 10.x addresses when configured for 192.x- Started by Philip Bondi
- Replies: 3
-
-
-
RT AX88U problem with update 3004 388-8-1 and 2: loss of internet access
- Started by eric le sauze
- Replies: 8
-
Loss of access to user interface after application of VPN rule and Killswitch (3004.388.8)
- Started by Unetwork
- Replies: 14
-
Latest threads
-
Asuswrt Merlin 3006.102.3 Alpha2 for GT-BE98 Pro, RT-BE86U, RT-BE88U, and RT-BE96U- Started by visortgw
- Replies: 0
-
-
-
-
Support SNBForums w/ Amazon
If you'd like to support SNBForums, just use this link and buy anything on Amazon. Thanks!
Sign Up For SNBForums Daily Digest
Get an update of what's new every day delivered to your mailbox. Sign up here!