CAT is the definition of specs that the cable should meet. All this other crap is being hopeful that will they make more money.
I don't want CCA cable regardless. They seem to hide that fact their cable is CCA.
Where to get good Patch cables
- Thread starter coxhaus
- Start date
I don't want CCA cable regardless. They seem to hide that fact their cable is CCA.
drinkingbird
Part of the Furniture
Yes, and the CAT specs do not have anything to do with POE. They are related to data communication. The power handling capability is strictly based on the gauge of the wire inside the cable, and the temperature rating.
A CAT3 20AWG will carry far more power with less voltage drop than a CAT8 30AWG. Of course it will only do 10 megabits of data reliably.
Both solid copper and CCA can easily meet all of the CAT specs, even CAT 8. They can also carry the same amount of power based on gauge. However a higher CAT cable will not necessarily be able to carry POE+ or POE++ (especially not type 4).
Depending on distance, POE++ Type 4 could very well need 20AWG conductors, which is going to be very hard/impossible to find. 22 AWG is available and should be ok, 23 AWG will do it at shorter distances. Granted POE++ uses 4 wires for + and 4 wires for - so that helps reduce the amount of current each wire must carry, but at the full 100 watts, you still need larger gauge wire. The current on each wire won't be exactly the same as the resistance will differ slightly, so it isn't as easy as dividing the total current for your application by 4 and selecting a gauge based on that.
Last edited:
NXIL
Regular Contributor
How long?
They are most likely not even Cat5e quality:
"The vast majority of cables sold as Category 6 or 6a, whether in brick-and-mortar establishments or online, simply do not meet the Category 6 or 6a specifications; we've put a lot of samples of a lot of other manufacturers' product through proper certification testing, and cables that actually pass spec are unusual. In fact, it's not uncommon for cables that are sold as "Cat 6" to even fail to meet Cat 5e specifications. Vendors get away with misrepresenting Ethernet patch cord performance because the average consumer isn't in a position to buy the $10,000 worth of gear it'll take to check his purchase against the spec. Here at Blue Jeans Cable we don't want to have anything to do with misrepresenting spec compliance -- every Ethernet patch cable we sell comes with its own individual test report, run on a Fluke DTX-1800 certification tester, showing that it meets or exceeds the applicable spec. If it doesn't, we won't sell it."
I think this is a very good article:
And no I do not work for BJC, but I just got some of their cables and they are really good.
Anyway, if you can afford these cables, I highly recommend them.
If you are more on a budget, then I truly think Monoprice is good enough. I would recommend their Cat6 cables, as these should handle 10gb out to 50 meter length or so, but, if you have a run that long, a solid wire cable is better than a patch cable, which are usually stranded.
Test report from one of the cables I got recently is attached. Great quality wire (Belden) and connectors.
Attachments
NXIL
Regular Contributor
CCA does not meet specs by definition, and is a marker of poor quality, like face tattoos. (Drinkingbird, if you have a face tattoo of a Flamingo with a dirty martini, I take that back!)
Weird: I cannot find that on their site either.
CAT6A ETHERNET CABLES - HDMI Cable, Home Theater Accessories, HDMI Products, Cables, Adapters, Video/Audio Switch, Networking, USB, Firewire, Printer Toner, and more!
Monoprice, Inc. (DBA. MonoPrice.com) specializes in the wholesale distribution of world class cable assemblies for home theater, PC, and high technology industries. MonoPrice.com offers a wide range of products from standard PC products, network cables, and HDMI cables to custom cable assemblies...
www.monoprice.com
I honestly think Monoprice Cat6 in 24 or 23 gauge is more than enough for OP:
NETWORKING PATCH CABLES - HDMI Cable, Home Theater Accessories, HDMI Products, Cables, Adapters, Video/Audio Switch, Networking, USB, Firewire, Printer Toner, and more!
Monoprice, Inc. (DBA. MonoPrice.com) specializes in the wholesale distribution of world class cable assemblies for home theater, PC, and high technology industries. MonoPrice.com offers a wide range of products from standard PC products, network cables, and HDMI cables to custom cable assemblies...
www.monoprice.com
And, I do not think OP needs shielded cables, but, I left them in the above length. (OP, shielding often causes more problems than it solves.)
Unless something changed, and I hope not, Monoprice only sells pure copper, no CCA.
drinkingbird
Part of the Furniture
Bluejeans has a vested interest in these tests and reviews....
NXIL
Regular Contributor
Didn't want to read this @degrub. Now my ocd will kick and have to replace cables. I know I have Monoprice cat 6 in wall. These
were put in during construction of our home. At least they are in conduit. To bad I just found this forum lately...
I found this thread Recommended Ethernet Cable Brands. And this reply @Trip here.
Edit: I looked at material on installer invoice, all in wall is Vertical Cable. Now I can just replace the other cables.
So do I. It works absolutely fine.
And vertical cable: looks to be pure copper only, no CCA, looks fine.
NXIL
Regular Contributor
Of course they do!
But they post their results, and, stand behind their products.
Belden and Mohawk have vested interests in testing too, as do auto manufactures, aircraft, pretty much any tech.
drinkingbird
Part of the Furniture
You'd be amazed at how much you're surrounded by CCA and/or CCS. Coax from cable companies (and most big box stores) has been CCA for a long time. I regularly see mention that it does not meet spec but have not seen it specifically called out in the spec, and likely it just hasn't been updated. 28AWG used to not be in the spec but was added. As long as the cable can pass the required frequency and meets the other requirements for crosstalk, capacitance, resistance, etc, it will be fine. I prefer pure copper just to know that the core isn't going to crack or wear faster than the clad with regular use, but in reality that's unlikely to happen.
You can find junk cables from lots of companies. Monoprice sells flat and ultra thin cables that are 32AWG and can't possibly meet the specs they claim to. Just gotta know what to look for, and barring that, stick with the higher priced professional brands.
drinkingbird
Part of the Furniture
The difference is those are tested by third parties out of house.
drinkingbird
Part of the Furniture
Agreed, you MUST ground one end, and one end only. Which is easier said than done. Doing it wrong actually turns it into an antenna or introduces a ground loop which leaves you worse off than UTP.
NXIL
Regular Contributor
Agree. I found them more than a decade ago on Slashdot, when IT/sysadmins were talking about patch cables, where to get them, whether to make them yourself (no, generally.)
As for bulk, I have used this
Monoprice Cat6 1000ft Green CMR UL Bulk Cable, Solid, UTP, 23AWG, 550MHz, Pure Bare Copper, Reelex II Pull Box, No Logo, Bulk Ethernet Cable - Monoprice.com
Monoprice™ brings you high quality bulk rolls of Ethernet cables at unparalleled value. This high performance bulk cabling is perfect for your custom network installation projects. You can cut l
www.monoprice.com
without any issues (and yes I know about the recall, I missed that batch of cable, but I thankfully also missed flying on the recalled Boeing 737 Max)
The Reelex 2 box is a sign it's not bargain basement level wire. Has plenty of certifications, and, that is where the recall started, they were checking on quality and found an issue. Monoprice replaced all the faulty wire, by the way, including installation. (No I do not work for them nor have I!)
NXIL
Regular Contributor
Belden did not get "sold to China".
Our History
www.belden.com
Belden has been doing the acquiring for some time now.
"I don't have access to a Fluke now so I am kind of working blind.
I have 1 Amazon cable that causes my POE+ wireless unit to run very hot."
Blue Jeans Cable (you get the fluke print out with it) or Monoprice Cat6, larger gauge, 23 gauge.
drinkingbird
Part of the Furniture
I haven't tried their bulk cable, mostly because I came into a bunch of spools of Panduit Cat6A and Superior Essex 5e which will last me a very long time. But really if you have the opportunity, run flex duct so that if you do have to replace cable later, it will be easy. Or at the very least, fish through pull string and leave it behind your plate and run to an accessible area. Not possible in all circumstances obviously but really makes things nice in the future.
I would probably consider their bulk solid cable but would do some more research on it, don't know enough about it since I haven't shopped for bulk in a while.
NXIL
Regular Contributor
Oh I agree! I also think Monoprice should not sell Cat7 (really?), and Cat8 isn't really necessary either.
The one time I have had trouble with a Monoprice cable was a thin Cat6a--it worked fine, but the RJ45 connector wouldn't release properly. Sucked.
drinkingbird
Part of the Furniture
Belden did not get "sold to China".
Our History
Belden has been doing the acquiring for some time now.
"I don't have access to a Fluke now so I am kind of working blind.
I have 1 Amazon cable that causes my POE+ wireless unit to run very hot."
Blue Jeans Cable (you get the fluke print out with it) or Monoprice Cat6, larger gauge, 23 gauge.
There are homemade speaker wires made out of tons of CAT cable braided together, takes forever but considered some of the best you can have for a fraction of the price of "audiophile" premade ones. The go-to for those is still a specific Belden cable. Their copper has been proven many times to be extremely low oxygen, and the jacket on each wire is thick and durable. They are a bit less common for CAT cables these days, at least in the US. I see a lot more Panduit and Commscope.
You are right it was Linksys and Belkin which was sold not Belden. I should have googled it. Must of been a senior moment.Belden did not get "sold to China".
Our History
Belden has been doing the acquiring for some time now.
"I don't have access to a Fluke now so I am kind of working blind.
I have 1 Amazon cable that causes my POE+ wireless unit to run very hot."
Blue Jeans Cable (you get the fluke print out with it) or Monoprice Cat6, larger gauge, 23 gauge.
Last edited:
drinkingbird
Part of the Furniture
Probably the same cables Monoprice sells.
Either get no name cables, or spend the money on the commercial grade ones mentioned. Monoprice cables, as long as you look at the specs and don't get the flat, slim, tiny AWG ones, will most likely be fine. At their prices, buy a couple extra, if one or two don't work, they'll refund you and probably tell you to toss them.
The only "in between" I can think of is Cables2Go, they are owned by Legrand but probably made in china from the same suppliers as everyone else.
Similar threads
Similar threads
| Thread starter | Title | Forum | Replies | Date |
|---|---|---|---|---|
|
Home Network Plan - Where and What | Switches, NICs and cabling | 20 |