What's new

Beta Asuswrt-Merlin 388.1 Beta is available for select models

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

Status
Not open for further replies.
I disabled Cake and re-enabled it again after a reboot. When I did this both accelerations were re-enabled.
 
has anyone any ideas how to cure this?
Some sites block IP addresses coming from known VPN providers, due to past abuses.

AX86U

388.1_beta2
dcd crashes are long-standing issue that Trend Micro seems to not care enough to fully address (there are many different causes for these dcd crashes). The issues have been there for years, and by now they are fully aware of their existence.

hi every 5 secs i am getting this error on AX88U beta2:
Your router is running out of memory. If you use any third party addon that can use a lot of memory (like Diversion with large lists), remove them.

Shouldn't Flow Cache be disabled?
There are so many scenarios that will enable/disable flow cache, since Asus hasn't implemented a robust way to do so, some of these events can incorrectly re-enable it without checking first if it should be kept disabled. Without knowing the exact scenario triggering this, it will be difficult to track down. You would need to trace back your steps to figure out which
 
I rebooted after enabling Cake and Flow Cache is disabled now. HW Accel is still enabled.

When you search the log, is there any call that reenables HW Acceleration after above entry?
I think here is what you want.

May 4 23:05:02 kernel: ===> Activate Deep Green Mode
May 4 23:05:02 kernel: dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
May 4 23:05:02 kernel: Broadcom Command List Driver v1.0
May 4 23:05:02 kernel: Initialized Runner Host Layer
May 4 23:05:02 kernel: Initialized Runner Unicast Layer
May 4 23:05:02 kernel: Initialized Runner L2 Unicast Layer
May 4 23:05:02 kernel: Initialized Runner Multicast Layer
May 4 23:05:02 kernel: Retrieve num_fhw_path=64
May 4 23:05:02 kernel: ^[[0;36;44mBroadcom Packet Flow Cache HW acceleration enabled.^[[0m
May 4 23:05:02 kernel: Enabled Runner binding to Flow Cache
May 4 23:05:02 kernel: Initialized Runner Protocol Layer (800)
May 4 23:05:02 kernel: Broadcom Runner Blog Driver Char Driver v0.1 Registered <3009>

And this as well.

May 4 23:05:02 kernel: DHD_FKB_POOL size is:1280 and entry size:2816
May 4 23:05:02 kernel: DHD_PKTTAG POOL size is:2592 and entry size:128
May 4 23:05:02 kernel: PCI_PROBE: bus 1, slot 0,vendor 14E4, device AAA4(good PCI location)
May 4 23:05:02 kernel: pcieh 0000:01:00.0: enabling device (0000 -> 0002)
May 4 23:05:02 kernel: dor0: runner supported ring format types TxP 0x5, RxP 0x3 TxC 0x3 RxC 0x3^M
May 4 23:05:02 kernel: dhd_runner_attach: Tx Offload - Enabled, Ring Size = 1024
May 4 23:05:02 kernel: dhd_runner_attach: Rx Offload - Enabled, Ring Size = 1024
May 4 23:05:02 kernel: TX wakeup info: reg = <0x82299004>, val = <0x10000000>
May 4 23:05:02 kernel: RX wakeup info: reg = <0x8229a004>, val = <0x28000000>
May 4 23:05:02 kernel: CFG80211-ERROR) wl_setup_wiphy : Registering Vendor80211
May 4 23:05:02 kernel: dhd_attach(): thread:dhd_watchdog_thread:275 started
May 4 23:05:02 kernel: Creating CPU ring for queue number 0 with 1024 packets descriptor=0xffffffbffc54a8c0
May 4 23:05:02 kernel: Creating CPU ring for queue number 1 with 1024 packets descriptor=0xffffffbffc54a900
May 4 23:05:02 kernel: ^[[1m^[[34m wfd_bind: Dev eth%d wfd_idx 0 wl_radio_idx 0 Type fkb configured WFD thread wfd0-thrd minQId/maxQId (8/9), status (0) qmask 0x3^[[0m
May 4 23:05:02 kernel: Instantiating WFD 0 thread
May 4 23:05:02 kernel: dor0: MSG Ring format set to 1
May 4 23:05:02 kernel: dhd_runner_flowmgr_init: dhd0_rnr bootmem addr<ffffffc00a600000> size<14680064>
May 4 23:05:02 kernel: dhd_runner_profile_init: N+M profile = 3 01:1024/0512 -1:2048/1024 -1:1024/0512 -1:0512/0512 00:0512/0512
May 4 23:05:02 kernel: dhd_runner_policy_init: N+M Policy = 0 1 (HW)
 
I rebooted after enabling Cake and Flow Cache is disabled now. HW Accel is still enabled.


I think here is what you want.

May 4 23:05:02 kernel: ===> Activate Deep Green Mode
May 4 23:05:02 kernel: dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
May 4 23:05:02 kernel: Broadcom Command List Driver v1.0
May 4 23:05:02 kernel: Initialized Runner Host Layer
May 4 23:05:02 kernel: Initialized Runner Unicast Layer
May 4 23:05:02 kernel: Initialized Runner L2 Unicast Layer
May 4 23:05:02 kernel: Initialized Runner Multicast Layer
May 4 23:05:02 kernel: Retrieve num_fhw_path=64
May 4 23:05:02 kernel: ^[[0;36;44mBroadcom Packet Flow Cache HW acceleration enabled.^[[0m
May 4 23:05:02 kernel: Enabled Runner binding to Flow Cache
May 4 23:05:02 kernel: Initialized Runner Protocol Layer (800)
May 4 23:05:02 kernel: Broadcom Runner Blog Driver Char Driver v0.1 Registered <3009>

And this as well.

May 4 23:05:02 kernel: DHD_FKB_POOL size is:1280 and entry size:2816
May 4 23:05:02 kernel: DHD_PKTTAG POOL size is:2592 and entry size:128
May 4 23:05:02 kernel: PCI_PROBE: bus 1, slot 0,vendor 14E4, device AAA4(good PCI location)
May 4 23:05:02 kernel: pcieh 0000:01:00.0: enabling device (0000 -> 0002)
May 4 23:05:02 kernel: dor0: runner supported ring format types TxP 0x5, RxP 0x3 TxC 0x3 RxC 0x3^M
May 4 23:05:02 kernel: dhd_runner_attach: Tx Offload - Enabled, Ring Size = 1024
May 4 23:05:02 kernel: dhd_runner_attach: Rx Offload - Enabled, Ring Size = 1024
May 4 23:05:02 kernel: TX wakeup info: reg = <0x82299004>, val = <0x10000000>
May 4 23:05:02 kernel: RX wakeup info: reg = <0x8229a004>, val = <0x28000000>
May 4 23:05:02 kernel: CFG80211-ERROR) wl_setup_wiphy : Registering Vendor80211
May 4 23:05:02 kernel: dhd_attach(): thread:dhd_watchdog_thread:275 started
May 4 23:05:02 kernel: Creating CPU ring for queue number 0 with 1024 packets descriptor=0xffffffbffc54a8c0
May 4 23:05:02 kernel: Creating CPU ring for queue number 1 with 1024 packets descriptor=0xffffffbffc54a900
May 4 23:05:02 kernel: ^[[1m^[[34m wfd_bind: Dev eth%d wfd_idx 0 wl_radio_idx 0 Type fkb configured WFD thread wfd0-thrd minQId/maxQId (8/9), status (0) qmask 0x3^[[0m
May 4 23:05:02 kernel: Instantiating WFD 0 thread
May 4 23:05:02 kernel: dor0: MSG Ring format set to 1
May 4 23:05:02 kernel: dhd_runner_flowmgr_init: dhd0_rnr bootmem addr<ffffffc00a600000> size<14680064>
May 4 23:05:02 kernel: dhd_runner_profile_init: N+M profile = 3 01:1024/0512 -1:2048/1024 -1:1024/0512 -1:0512/0512 00:0512/0512
May 4 23:05:02 kernel: dhd_runner_policy_init: N+M Policy = 0 1 (HW)
Does your router correctly reboot after you enable cake?
 
Found out that without flow cache enabled I cant achieve 1 gig speeds on any device. But having flow cache enabled Wireguard wont work anymore. Why is that? Should I just disable wireguard VPN on my router and not use it on VPN Director to my NAS and instead install Windows software for Wireguard on my NAS to achieve better speeds for all devices in my network. I really wish that I could use my router for this.
 
Retracing my steps, I remembered enabling this and configuring my PS4 to use it.

ASUS-Wireless-Router-RT-AX88U-Game-Boost.png

Disabling it did nothing. Even after a reboot.
 
Does your router correctly reboot after you enable cake?
Funny you should say that. When I enabled it after my reset to defaults, yes it needed a reboot right away. However when disabling and re-enabling with a elective reboot in between, the router does not require a reboot upon enabling.
 
Found out that without flow cache enabled I cant achieve 1 gig speeds on any device. But having flow cache enabled Wireguard wont work anymore. Why is that? Should I just disable wireguard VPN on my router and not use it on VPN Director to my NAS and instead install Windows software for Wireguard on my NAS to achieve better speeds for all devices in my network. I really wish that I could use my router for this.
At the non-technical level, Wireguard and Broadcom's AX chipsets just don't play nicely together. Furthermore, disabling Flow Control will limit the speed for all devices, not just those on the VPN tunnels. As noted in previous threads if you want to use Wireguard with a fast ISP, don't run it on the router. Whether you can get better results by moving Wireguard to another host (your NAS, a Pi, something else) is for others to advise.
 
When I disable HW Accel or Runner as its called by command line( fc config --hw-accel 0 ), there is no log entry marking the event..
 
At the non-technical level, Wireguard and Broadcom's AX chipsets just don't play nicely together. Furthermore, disabling Flow Control will limit the speed for all devices, not just those on the VPN tunnels. As noted in previous threads if you want to use Wireguard with a fast ISP, don't run it on the router. Whether you can get better results by moving Wireguard to another host (your NAS, a Pi, something else) is for others to advise.

Thank you for explaining. I understand now better. I will stay on beta2 but will disable wireguard from router for now and use it on NAS.
 
I can also enable both Accelerations but it has no effect on my speed test results, through Wireguard.
 
@RMerlin RT-AX86U, 388.1_beta2, some difficulties to connect to 5G. Most of the clients are not able to connect to 5G, after some time some of them are able to connect. The following errors
Nov 13 13:17:29 bsd: bsd: Sending act Frame to a0:...............:10 with transition target eth7 ssid 3c:.............:2c
Nov 13 13:17:30 bsd: bsd: BSS Transit Response: ifname=eth6, event=156, token=3, status=7, mac=00:00:00:00:00:00
Nov 13 13:17:30 bsd: bsd: BSS Transit Response: STA reject
Nov 13 13:17:30 bsd: bsd: Skip STA:a0:......:10 reject BSSID
 
Last edited:
Installed beta2 on my AX86U and got the following during boot (never saw this with previous 386 firmwares). Do I have to worry about? Everything seems normal so far.

Code:
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa0000
May  5 07:05:11 kernel: brcmboard registered
May  5 07:05:11 kernel: genirq: Flags mismatch irq 34. 00000000 (brcm_34) vs. 00000000 (brcm_34)
May  5 07:05:11 kernel: gluebi (pid 1): gluebi_resized: got update notification for unknown UBI device 0 volume 0
May  5 07:05:11 kernel: bcmswlpbk0 (Ext switch port: 8) (Logical Port: 8) Virtual link DOWN
May  5 07:05:11 kernel: bcm_enet_init:L2453 ENET system contructed and configured enet-kthrd thread
May  5 07:05:11 kernel: enet_kthread_handler:L296 Instantiating ENET thread
May  5 07:05:11 kernel: Lservices Loaded - NComm, Inc.
May  5 07:05:11 kernel: exLinuxETH Loaded - NComm, Inc.
May  5 07:05:11 kernel: broadcomThermalDrv brcm-therm: init (CPU count 4 4 4 4)
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa0000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa0800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa1200
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa1800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa2000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa2800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa3000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa3800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa4000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa4800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa5200
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa5800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa6000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa6800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa7000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa7800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa8000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa8800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa9200
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa9800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa0000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa0800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa1000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa1800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa2000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa2800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa3000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa3800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa4000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa4800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa5000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa5800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa6000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa6800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa7000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa7800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa8000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa8800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa9000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa9800
May  5 07:05:11 kernel: bcmswlpbk0 (Ext switch port: 8) (Logical Port: 8) Virtual link UP
May  5 07:05:11 kernel: eth5 (Ext switch port: 7) (Logical Port: 15) (phyId: 1e) Link Up at 1000 mbps full duplex
May  5 07:05:11 kernel: hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19)

Edit: After a second reboot these lines did not appear again. Could it be "normal" during initializing with new 388 firmware?
 
Last edited:
Well, not sure how much is it considered as a bug, but worth mention it.
Beta2, Ax88U

The WiFi 5Ghz is having hard time to start broadcast.
It takes 2-3 min, used to happen when Ch control was set to auto.
Now it fixed to a certain channel and still takes 2-3 min.

On Beta1 everything was just fine.
Any known changes to AX88U between 2 Beta?

Not sure why.
 
Installed beta2 on my AX86U and got the following during boot (never saw this with previous 386 firmwares). Do I have to worry about? Everything seems normal so far.

Code:
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa0000
May  5 07:05:11 kernel: brcmboard registered
May  5 07:05:11 kernel: genirq: Flags mismatch irq 34. 00000000 (brcm_34) vs. 00000000 (brcm_34)
May  5 07:05:11 kernel: gluebi (pid 1): gluebi_resized: got update notification for unknown UBI device 0 volume 0
May  5 07:05:11 kernel: bcmswlpbk0 (Ext switch port: 8) (Logical Port: 8) Virtual link DOWN
May  5 07:05:11 kernel: bcm_enet_init:L2453 ENET system contructed and configured enet-kthrd thread
May  5 07:05:11 kernel: enet_kthread_handler:L296 Instantiating ENET thread
May  5 07:05:11 kernel: Lservices Loaded - NComm, Inc.
May  5 07:05:11 kernel: exLinuxETH Loaded - NComm, Inc.
May  5 07:05:11 kernel: broadcomThermalDrv brcm-therm: init (CPU count 4 4 4 4)
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa0000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa0800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa1200
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa1800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa2000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa2800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa3000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa3800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa4000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa4800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa5200
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa5800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa6000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa6800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa7000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa7800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa8000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa8800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa9200
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa9800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa0000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa0800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa1000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa1800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa2000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa2800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa3000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa3800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa4000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa4800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa5000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa5800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa6000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa6800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa7000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa7800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa8000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa8800
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa9000
May  5 07:05:11 kernel: bcm63xx_nand ff801800.nand: uncorrectable error at 0xa9800
May  5 07:05:11 kernel: bcmswlpbk0 (Ext switch port: 8) (Logical Port: 8) Virtual link UP
May  5 07:05:11 kernel: eth5 (Ext switch port: 7) (Logical Port: 15) (phyId: 1e) Link Up at 1000 mbps full duplex
May  5 07:05:11 kernel: hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19)

Thats quite a few bad blocks. The nand device on most any router will have some bad blocks. But, as long as the mtd driver is doing it's job, it would mark them as bad and unusable.
You will have less available storage on the partition(s) that those blocks are on - but as you said - everything seems normal.
 
Well, not sure how much is it considered as a bug, but worth mention it.
Beta2, Ax88U

The WiFi 5Ghz is having hard time to start broadcast.
It takes 2-3 min, used to happen when Ch control was set to auto.
Now it fixed to a certain channel and still takes 2-3 min.

On Beta1 everything was just fine.
Any known changes to AX88U between 2 Beta?

Not sure why.
No issues here. Auto channel enabled, (but no DFS channels).
 
You are using a mix of filtered, Quad9, and unfiltered, Cloudflare DNS resolvers which is not giving you the best protection from malware and other bad actors.
I recommend you use Cloudflare Security with Quad9. It is a manual entry with anycast addresses of 1.1.1.2 and 1.0.0.2 and TLS Hostname of security.cloudflare-dns.com
IPV6 for Cloudflare Security would end in 1112 and 1002
For better performance I would alternate IPV4 and IPV6 addresses.
Better yet just stick with Quad9!
 
Status
Not open for further replies.

Similar threads

Support SNBForums w/ Amazon

If you'd like to support SNBForums, just use this link and buy anything on Amazon. Thanks!

Sign Up For SNBForums Daily Digest

Get an update of what's new every day delivered to your mailbox. Sign up here!
Top