Beta [FORK] [DSL] [TESTERS] GNUton's Alpha/Beta Merlin builds
Yes, I did enable SSH on admin Page. Check the screenshot.
Attachments
Last edited:
SomeWhereOverTheRainBow
Part of the Furniture
do you have all your winscp settings set right for your host:
correct user name, password, address, and protocol?
everything is correct. still not working. I am able to login to the temp folder but transferring file is failing.
SomeWhereOverTheRainBow
Part of the Furniture
You could also use putty, log into the , download the firmware using wget.
Just uploaded to the latest Beta for my DSL AX82U and first off I noticed when setting up a warning page is missing, once I got in to my route I started setting bits up but noticed out of the corner of my eye that the RGB was off, I then rebooted the router the RGB went red like normal then once it loaded in the RGB turned off! not blue like default.
This is a copy of the page that was missing.
After I notice the above problems, I thought to my self I revert back to the 386.5_0_2-Gnuton, trying to do so I got unsuccessful flash, I Soft reset via restore factory defaults in the UI, rebooted and I tried again, and the 2ed time it flashed, after that flashed I then Hard reset the router then soft reset. and loaded my old settings.
But I can not believe the RGB is not working it was buggy in the last stable release as I reported, sure you would of checked the basics
This is a copy of the page that was missing.
After I notice the above problems, I thought to my self I revert back to the 386.5_0_2-Gnuton, trying to do so I got unsuccessful flash, I Soft reset via restore factory defaults in the UI, rebooted and I tried again, and the 2ed time it flashed, after that flashed I then Hard reset the router then soft reset. and loaded my old settings.
But I can not believe the RGB is not working it was buggy in the last stable release as I reported, sure you would of checked the basics
This is how I connect to SSH using windows 11 default.
Windows 11 Lastest SSH Setup
First start a command prompt then run power shell, then in power shell run the below command.
# This checks to see if openssh is installed on the system.
Get-WindowsCapability -Online | Where-Object Name -like 'OpenSSH*'
once the check is done. by default client was installed yet the server was not so only run the open ssh server commands
# Install the OpenSSH Client
Add-WindowsCapability -Online -Name OpenSSH.Client~~~~0.0.1.0
# Install the OpenSSH Server
Add-WindowsCapability -Online -Name OpenSSH.Server~~~~0.0.1.0
Once done i then run the commands we need to start the openssh system service
# Start the sshd service
Start-Service sshd
# OPTIONAL but recommended:
Set-Service -Name sshd -StartupType 'Manual'
Once thats done type ssh then the router admin user name follower by the host name of your router also need to include the port so it would be
ssh -p 2204 admin@myrouter
Once finished with SSH i then run from Powershell Stop-Service sshd
Windows 11 Lastest SSH Setup
First start a command prompt then run power shell, then in power shell run the below command.
# This checks to see if openssh is installed on the system.
Get-WindowsCapability -Online | Where-Object Name -like 'OpenSSH*'
once the check is done. by default client was installed yet the server was not so only run the open ssh server commands
# Install the OpenSSH Client
Add-WindowsCapability -Online -Name OpenSSH.Client~~~~0.0.1.0
# Install the OpenSSH Server
Add-WindowsCapability -Online -Name OpenSSH.Server~~~~0.0.1.0
Once done i then run the commands we need to start the openssh system service
# Start the sshd service
Start-Service sshd
# OPTIONAL but recommended:
Set-Service -Name sshd -StartupType 'Manual'
Once thats done type ssh then the router admin user name follower by the host name of your router also need to include the port so it would be
ssh -p 2204 admin@myrouter
Once finished with SSH i then run from Powershell Stop-Service sshd
Sure mate, once you installed the new firmware, then restore factory, you get the set up wizard in that you select manual then set up, once you entered wifi name and pass I would then click next then get the above screen then next and I would get the router name and pass page. Yet in the beta the above was missing can not conferm more as on your older release
P.s So the RGB is work in progress
P.s So the RGB is work in progress
Last edited:
Zendilar
Regular Contributor
I am testing 386.07_0-gnuton0_alpha0 for a week now on my DSL-AC68U and it factions normally, I don't see any instability.
The only issue that I had was the NVRAM is getting full again, so I had to ssh the usual command
(for line in `nvram show | grep =$ `; do var=${line%*=}; nvram unset $var; done; nvram commit)
to make it go back to the normal amount again.
The only issue that I had was the NVRAM is getting full again, so I had to ssh the usual command
(for line in `nvram show | grep =$ `; do var=${line%*=}; nvram unset $var; done; nvram commit)
to make it go back to the normal amount again.
@GNUton
Have had the current 386.07_0-gnuton0_beta1 running on my RT-AX82U , working great by the way. The only small problem, I have, is that the router picture is not displaying, node pictures display without any issue, and phone app also displays ALL router pictures without any issue. Have attached a screen dump of the error from gui, using the F12 develpment console, from Chrome.
Note I have tried multiple full resets and different browsers, clearing cache.. No ad blocking software.
Current GUI URL:
https://nw-dlcdnet.asus.com/plugin/productIcons/RT-AX82U_CB_0.png - does not work - 404 error not found. The requested URL was not found on this server.
Change the above GUI URL, to this link within the browser:
https://nw-dlcdnet.asus.com/plugin/productIcons/RT-AX82U.png - works, an image is found
Have had the current 386.07_0-gnuton0_beta1 running on my RT-AX82U , working great by the way. The only small problem, I have, is that the router picture is not displaying, node pictures display without any issue, and phone app also displays ALL router pictures without any issue. Have attached a screen dump of the error from gui, using the F12 develpment console, from Chrome.
Note I have tried multiple full resets and different browsers, clearing cache.. No ad blocking software.
Current GUI URL:
https://nw-dlcdnet.asus.com/plugin/productIcons/RT-AX82U_CB_0.png - does not work - 404 error not found. The requested URL was not found on this server.
Change the above GUI URL, to this link within the browser:
https://nw-dlcdnet.asus.com/plugin/productIcons/RT-AX82U.png - works, an image is found
Attachments
Last edited:
GNUton
Senior Member
@Neil62 thanks for reporting this. The image comes as you see comes from asus. I will double check this.
you can track the progress of this issue here: https://github.com/gnuton/asuswrt-merlin.ng/issues/205
you can track the progress of this issue here: https://github.com/gnuton/asuswrt-merlin.ng/issues/205
Zendilar
Regular Contributor
you are the best mate.
Thanks for following through on this, much appreciated.
GNUton
Senior Member
@TrebleTA http://router.asus.com/Advanced_ADSL_Content.asp already support vectoring (G998.4/G.INP) and B is also already available for VDSL.
Similar threads
Similar threads
Similar threads
-
-
-
-
-
DSL-AC68U - Configuration panels on GUI have disappeared
- Started by chrisisbd
- Replies: 1
-
-
Having major difficulties setting up a VLAN ID on DSL-AX82U
- Started by albina19590
- Replies: 0
-
-
Where to Download GNUton's Asus Merlin For DSL-AC68U
- Started by Combe_Charmer
- Replies: 16
-