Menu
What's new
By:
Filters Better Search

modmon modmon - WebUI for monitoring Virgin Hub 3 cable modem stats

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

Would graphing Virgin Media Superhub 3 stats from Merlin be useful for you?

  • Yes

    Votes: 13 86.7%

  • No

    Votes: 2 13.3%
  • Total voters
    15
  • Poll closed .
For those asking "Is X supported"

The requirements are that your modem exposes the relevant raw data (e.g. SNMP OIDs) for the channel stats etc. behind an unauthenticated page. For example, Virgin Hub 3 hosts this at http://192.168.100.1/getRouterStatus

The output needs to look similar to the below snippet:
Code: 
{"1.3.6.1.4.1.4115.1.3.4.1.5.9.0":"10",
"1.3.6.1.4.1.4115.1.3.3.1.1.1.3.1.0":"1",
"1.3.6.1.4.1.4491.2.1.14.1.5.4.0":"1",
"1.3.6.1.2.1.10.127.1.1.5.0":"4",
"1.3.6.1.2.1.126.1.1.1.1.1.2":"1",
"1.3.6.1.2.1.69.1.4.5.0":"fewfvcervbreberb",
"1.3.6.1.2.1.10.127.1.1.4.1.3.1":"7776476",
"1.3.6.1.2.1.10.127.1.1.4.1.4.1":"0",
"1.3.6.1.2.1.10.127.1.1.4.1.5.1":"376",
"1.3.6.1.4.1.4491.2.1.20.1.24.1.1.1":"376",
"1.3.6.1.2.1.10.127.1.1.4.1.3.2":"1791416",
"1.3.6.1.2.1.10.127.1.1.4.1.4.2":"0",
"1.3.6.1.2.1.10.127.1.1.4.1.5.2":"386",
"1.3.6.1.4.1.4491.2.1.20.1.24.1.1.2":"386",
"1.3.6.1.2.1.10.127.1.1.4.1.3.3":"1713067",
"1.3.6.1.2.1.10.127.1.1.4.1.4.3":"0",
"1.3.6.1.2.1.10.127.1.1.4.1.5.3":"389",
"1.3.6.1.4.1.4491.2.1.20.1.24.1.1.3":"389",
"1.3.6.1.2.1.10.127.1.1.4.1.3.4":"1669590",
"1.3.6.1.2.1.10.127.1.1.4.1.4.4":"0",
"1.3.6.1.2.1.10.127.1.1.4.1.5.4":"389",
"1.3.6.1.4.1.4491.2.1.20.1.24.1.1.4":"389",
"1.3.6.1.2.1.10.127.1.1.4.1.3.5":"1700259",
"1.3.6.1.2.1.10.127.1.1.4.1.4.5":"0",
 
came across this today which has some detailed/technical info on the DOCSIS standards
https://community.virginmedia.com/t...ICAL-PRIMER-updated-October-2016/td-p/2271297

I noticed the info/links below:
Please note that at this time of writing, the RS counts are not available on the HUB 3 except via a URL:
http://192.168.0.1/walk?oids=1.3.6.1.2.1.10.127.1.1.4.1.3 for Pre-RS errors
http://192.168.0.1/walk?oids=1.3.6.1.2.1.10.127.1.1.4.1.4 for Post-RS errors

@Jack Yaz - Is the Pre-RS stats worth keeping a track of? The values for Post-RS errors are always 0 on my Superhub 3.0 but looking at the Pre-RS errors I do see values there, e.g.
Code: 
{
"1.3.6.1.2.1.10.127.1.1.4.1.3.3":"552",
"1.3.6.1.2.1.10.127.1.1.4.1.3.48":"865",
"1.3.6.1.2.1.10.127.1.1.4.1.3.49":"609",
"1.3.6.1.2.1.10.127.1.1.4.1.3.50":"611",
"1.3.6.1.2.1.10.127.1.1.4.1.3.51":"585",
"1.3.6.1.2.1.10.127.1.1.4.1.3.52":"404",
"1.3.6.1.2.1.10.127.1.1.4.1.3.53":"593",
"1.3.6.1.2.1.10.127.1.1.4.1.3.54":"636",
"1.3.6.1.2.1.10.127.1.1.4.1.3.55":"545",
"1.3.6.1.2.1.10.127.1.1.4.1.3.56":"749",
"1.3.6.1.2.1.10.127.1.1.4.1.3.57":"530",
"1.3.6.1.2.1.10.127.1.1.4.1.3.58":"369",
"1.3.6.1.2.1.10.127.1.1.4.1.3.59":"312",
"1.3.6.1.2.1.10.127.1.1.4.1.3.60":"627",
"1.3.6.1.2.1.10.127.1.1.4.1.3.61":"825",
"1.3.6.1.2.1.10.127.1.1.4.1.3.62":"1125",
"1.3.6.1.2.1.10.127.1.1.4.1.3.63":"601",
"1.3.6.1.2.1.10.127.1.1.4.1.3.64":"392",
"1.3.6.1.2.1.10.127.1.1.4.1.3.65":"415",
"1.3.6.1.2.1.10.127.1.1.4.1.3.66":"398",
"1.3.6.1.2.1.10.127.1.1.4.1.3.67":"357",
"1.3.6.1.2.1.10.127.1.1.4.1.3.68":"453",
"1.3.6.1.2.1.10.127.1.1.4.1.3.69":"509",
"1.3.6.1.2.1.10.127.1.1.4.1.3.70":"841",
"1":"Finish"
}
seen at http://192.168.100.1/walk?oids=1.3.6.1.2.1.10.127.1.1.4.1.3
 
Last edited:
What about the Cable Haunt security risk? Has that been dealt with? I block IP 192.168.100.1 on my router. There is no access.
 
Found this by fluke. VM have been shocking last week or so. Cheers! Sorry for the hijack but is there a know way of rebooting the SH3 remotely. I know they disabled SSH. Be great to reboot the SH3 when the ASUS router reboots for example
 
CMc said:
Found this by fluke. VM have been shocking last week or so. Cheers! Sorry for the hijack but is there a know way of rebooting the SH3 remotely. I know they disabled SSH. Be great to reboot the SH3 when the ASUS router reboots for example
Click to expand...
You can reboot it through the normal web interface if that's what you mean.
 
JonEngland said:
came across this today which has some detailed/technical info on the DOCSIS standards
https://community.virginmedia.com/t...ICAL-PRIMER-updated-October-2016/td-p/2271297

I noticed the info/links below:
Please note that at this time of writing, the RS counts are not available on the HUB 3 except via a URL:
http://192.168.0.1/walk?oids=1.3.6.1.2.1.10.127.1.1.4.1.3 for Pre-RS errors
http://192.168.0.1/walk?oids=1.3.6.1.2.1.10.127.1.1.4.1.4 for Post-RS errors

@Jack Yaz - Is the Pre-RS stats worth keeping a track of? The values for Post-RS errors are always 0 on my Superhub 3.0 but looking at the Pre-RS errors I do see values there, e.g.
Code: 
{
"1.3.6.1.2.1.10.127.1.1.4.1.3.3":"552",
"1.3.6.1.2.1.10.127.1.1.4.1.3.48":"865",
"1.3.6.1.2.1.10.127.1.1.4.1.3.49":"609",
"1.3.6.1.2.1.10.127.1.1.4.1.3.50":"611",
"1.3.6.1.2.1.10.127.1.1.4.1.3.51":"585",
"1.3.6.1.2.1.10.127.1.1.4.1.3.52":"404",
"1.3.6.1.2.1.10.127.1.1.4.1.3.53":"593",
"1.3.6.1.2.1.10.127.1.1.4.1.3.54":"636",
"1.3.6.1.2.1.10.127.1.1.4.1.3.55":"545",
"1.3.6.1.2.1.10.127.1.1.4.1.3.56":"749",
"1.3.6.1.2.1.10.127.1.1.4.1.3.57":"530",
"1.3.6.1.2.1.10.127.1.1.4.1.3.58":"369",
"1.3.6.1.2.1.10.127.1.1.4.1.3.59":"312",
"1.3.6.1.2.1.10.127.1.1.4.1.3.60":"627",
"1.3.6.1.2.1.10.127.1.1.4.1.3.61":"825",
"1.3.6.1.2.1.10.127.1.1.4.1.3.62":"1125",
"1.3.6.1.2.1.10.127.1.1.4.1.3.63":"601",
"1.3.6.1.2.1.10.127.1.1.4.1.3.64":"392",
"1.3.6.1.2.1.10.127.1.1.4.1.3.65":"415",
"1.3.6.1.2.1.10.127.1.1.4.1.3.66":"398",
"1.3.6.1.2.1.10.127.1.1.4.1.3.67":"357",
"1.3.6.1.2.1.10.127.1.1.4.1.3.68":"453",
"1.3.6.1.2.1.10.127.1.1.4.1.3.69":"509",
"1.3.6.1.2.1.10.127.1.1.4.1.3.70":"841",
"1":"Finish"
}
seen at http://192.168.100.1/walk?oids=1.3.6.1.2.1.10.127.1.1.4.1.3
Click to expand...

I just started getting Post-RS errors yesterday, and it appears to have jumped up a ways. The Downstream SNR is well above 34dB so that looks ok, but has anyone else seen these levels of Post-RS errors, is it something I should be concerned about and maybe contact Virgin?
upload_2020-5-26_19-23-37.png
 
That's perfectly normal in my experience with VM and doesn't usually indicate a problem. Consider that when there is disruption of any sort on your node (e.g. maintenance, faults, etc.) it will generate a lot of errors on your modem. After the fault/maintenance has cleared the number of errors should not increase any more. It is only a concern if the errors are increasing all the time. Unfortunately the only way I know of resetting the error counters is to reboot the modem.
 
ColinTaylor said:
That's perfectly normal in my experience with VM and doesn't usually indicate a problem. Consider that when there is disruption of any sort on your node (e.g. maintenance, faults, etc.) it will generate a lot of errors on your modem. After the fault/maintenance has cleared the number of errors should not increase any more. It is only a concern if the errors are increasing all the time. Unfortunately the only way I know of resetting the error counters is to reboot the modem.
Click to expand...

I was considering resetting the modem, but think I'll just keep an eye on it to check it stays level, good to know thanks
 
@Jack Yaz I have a RT-AC5300 running .17 Merlin Firmware. Modmon installed fine. I have a Hitron cda3-35 modem and http://192.168.100.1/getRouterStatus brings up the stats page.

When I run the Check Stas now from within Modmon I get Something went wrong trying to retrieve cable modem stats error.

Any ideas?

Thanks
 
Svenskmat said:
@Jack Yaz I have a RT-AC5300 running .17 Merlin Firmware. Modmon installed fine. I have a Hitron cda3-35 modem and http://192.168.100.1/getRouterStatus brings up the stats page.

When I run the Check Stas now from within Modmon I get Something went wrong trying to retrieve cable modem stats error.

Any ideas?

Thanks
Click to expand...
Can you PM me the output of
Code: 
/usr/sbin/curl -fs --retry 3 --connect-timeout 15 "http://192.168.100.1/getRouterStatus"
please? I suspect the parsing is failing
 
Jack Yaz said:
Can you PM me the output of
Code: 
/usr/sbin/curl -fs --retry 3 --connect-timeout 15 "http://192.168.100.1/getRouterStatus"
please? I suspect the parsing is failing
Click to expand...
Here is the output from that command
<html><head></head><body>
This document has moved to a new <a href="http://192.168.100.1/l ogin.html">location</a>.
Please update your documents to reflect the new location.
</body></html>

I do not have the stats shown in txt format you showed above.. so I guess it will not work for me
I have this page as the front page

upload_2020-5-31_10-6-29.png


And this page shows my stats

upload_2020-5-31_10-29-19.png


Am I out of luck to use Modmon?

Thanks for making this and your support
 
I added this thread to my watch list. Maybe one day my ISP’s Arris DG2470A will be supported.


09797F89-0DEB-45A2-A166-D616E9A50937.jpeg
23D3A591-2132-4366-8F48-303564A873B9.jpeg
 
Last edited:
SOOO Disappointed. My ISP's Arris 8200a has been running some really dusty firmware "D31CM-PEREGRINE-1.1.1.0-GA-03-NOSH" for years. It did not have the /getRouterStatus URL.

This morning they FINALLY did the major upgrade to "AB01.01.009.36.02_022720_183.0A.NSH" but sadly it still doesn't have the Status page. I really thought it would.

It does have a static html page:
http://192.168.100.1/cmconnectionstatus.html
Which looks like this:
upload_2020-7-3_8-42-34.png


Not sure this can be parsed... thoughts?
 
Last edited:
@RMerlin Here's another to move to the addons forum. It's a little dusty but for those it works for, its great.
 
Jack Yaz said:
If the modem provides SNMP/OIDs without needing to authenticate, I can take a look
Click to expand...
@ Jack Yaz, is there a way I can provide you with the appropriate information for my Netgear modem (CM1150V) to be compatible? I would like to see if this nifty little tool would become available for my modem. Thanks!
 
Last edited:
Jack Yaz said:
For those asking "Is X supported"

The requirements are that your modem exposes the relevant raw data (e.g. SNMP OIDs) for the channel stats etc. behind an unauthenticated page. For example, Virgin Hub 3 hosts this at http://192.168.100.1/getRouterStatus

The output needs to look similar to the below snippet:
Code: 
{"1.3.6.1.4.1.4115.1.3.4.1.5.9.0":"10",
"1.3.6.1.4.1.4115.1.3.3.1.1.1.3.1.0":"1",
"1.3.6.1.4.1.4491.2.1.14.1.5.4.0":"1",
"1.3.6.1.2.1.10.127.1.1.5.0":"4",
"1.3.6.1.2.1.126.1.1.1.1.1.2":"1",
"1.3.6.1.2.1.69.1.4.5.0":"fewfvcervbreberb",
"1.3.6.1.2.1.10.127.1.1.4.1.3.1":"7776476",
"1.3.6.1.2.1.10.127.1.1.4.1.4.1":"0",
"1.3.6.1.2.1.10.127.1.1.4.1.5.1":"376",
"1.3.6.1.4.1.4491.2.1.20.1.24.1.1.1":"376",
"1.3.6.1.2.1.10.127.1.1.4.1.3.2":"1791416",
"1.3.6.1.2.1.10.127.1.1.4.1.4.2":"0",
"1.3.6.1.2.1.10.127.1.1.4.1.5.2":"386",
"1.3.6.1.4.1.4491.2.1.20.1.24.1.1.2":"386",
"1.3.6.1.2.1.10.127.1.1.4.1.3.3":"1713067",
"1.3.6.1.2.1.10.127.1.1.4.1.4.3":"0",
"1.3.6.1.2.1.10.127.1.1.4.1.5.3":"389",
"1.3.6.1.4.1.4491.2.1.20.1.24.1.1.3":"389",
"1.3.6.1.2.1.10.127.1.1.4.1.3.4":"1669590",
"1.3.6.1.2.1.10.127.1.1.4.1.4.4":"0",
"1.3.6.1.2.1.10.127.1.1.4.1.5.4":"389",
"1.3.6.1.4.1.4491.2.1.20.1.24.1.1.4":"389",
"1.3.6.1.2.1.10.127.1.1.4.1.3.5":"1700259",
"1.3.6.1.2.1.10.127.1.1.4.1.4.5":"0",
Click to expand...
This is the only thing i could find on my modem....doubt it will help at all though:
 

Attachments

  • 20201013_234259.jpg
    20201013_234259.jpg
    145 KB · Views: 188
Quick question.

How is this any different from the information that a cable modem webui already provides?
 
You must log in or register to reply here.
Similar threads
Thread starter Title Forum Replies Date
RMerlin Incoming webui changes in 3006 Asuswrt-Merlin AddOns 3
A Addon tabs not propagating correctly in WebUI of GT-BE98_Pro on F/W v3006.102.1 Asuswrt-Merlin AddOns 2
kernol Diversion AC Merlinware 386.14 introduces screen scrolling problem on MANY [but not all] webui add-ons! Asuswrt-Merlin AddOns 36
thelonelycoder uiDivStats uiDivstats 4.0.5 - WebUI Stats for Diversion, December 15, 2024 Asuswrt-Merlin AddOns 70
HUNited vnStat WebUI page not found vnStat & connmon Asuswrt-Merlin AddOns 3
H WAN monitoring….. Asuswrt-Merlin AddOns 9
C Skynet Skynet Statistics Monitoring From - N/A Log Size - N/A Asuswrt-Merlin AddOns 6
L traffic monitoring issues Asuswrt-Merlin AddOns 4

Similar threads

Latest threads

Support SNBForums w/ Amazon

If you'd like to support SNBForums, just use this link and buy anything on Amazon. Thanks!

Sign Up For SNBForums Daily Digest

Get an update of what's new every day delivered to your mailbox. Sign up here!

Staff online

Members online

Total: 805 (members: 27, guests: 778)
Top