[Official] RT-AC87U Firmware version 3.0.0.4.378.9313

[Maastricht]

I have done several FW updates before, but when trying to upload the newest (.9313) I get the message: "Firmware upgrade unsuccessful. This may result from incorrect image or error transmission. Please check the version of firmware and try again."
I tried several times and as well as with the FW-version on the official site as the one mentioned in the top of this thread.
Any idea?

 

[fax]

Just reboot the router and if not enough reset to factory default before upgrading.

 

[fax]

BTW, this build fix a bug on VPN Client (OpenVPN) that I have reported on 9177 and earlier betas.
http://www.snbforums.com/threads/beta-rt-ac87u-9-0-0-4-378-9110.27280/page-2#post-207397

 

[Maastricht]

Just reboot the router and if not enough reset to factory default before upgrading.

Rebooting did the job!
I rebooted the router and immediately after that I uploaded the new FW. All went well. After that I did another reboot.

 

[bradbort]

I've installed it. No reboot or reset needed. 12 hours in, everything seems fine.

 

[bradbort]

Since this recent update, my log file has calmed way down. The only things I'm seeing are:

Nov 7 05:35:37 miniupnpd[709]: upnp_event_recv: recv(): Connection reset by peer
Nov 7 05:53:20 kernel: htb: htb qdisc 14: is non-work-conserving?
Nov 7 05:59:57 ntp: start NTP update
Nov 7 06:12:39 miniupnpd[709]: upnp_event_recv: recv(): Connection reset by peer
Nov 7 06:20:14 rc_service: httpd 437:notify_rc restart_wireless
Nov 7 06:20:20 kernel: wl_module_init: passivemode set to 0x0
Nov 7 06:20:20 kernel: wl_module_init: igs set to 0x0
Nov 7 06:20:20 kernel: wl_module_init: txworkq set to 0x1
Nov 7 06:20:20 kernel: eth1: Broadcom BCM4360 802.11 Wireless Controller 6.37.14.105 (r485445)
Nov 7 06:21:37 miniupnpd[709]: upnp_event_recv: recv(): Connection reset by peer
Nov 7 06:21:50 rc_service: httpd 437:notify_rc restart_wireless
Nov 7 06:21:56 kernel: wl_module_init: passivemode set to 0x0
Nov 7 06:21:56 kernel: wl_module_init: igs set to 0x0
Nov 7 06:21:56 kernel: wl_module_init: txworkq set to 0x1
Nov 7 06:21:56 kernel: eth1: Broadcom BCM4360 802.11 Wireless Controller 6.37.14.105 (r485445)
Nov 7 06:22:41 miniupnpd[709]: upnp_event_recv: recv(): Connection reset by peer
Nov 7 06:59:57 ntp: start NTP update
Nov 7 07:21:40 miniupnpd[709]: upnp_event_recv: recv(): Connection reset by peer
Nov 7 07:59:57 ntp: start NTP update
Nov 7 08:07:40 miniupnpd[709]: upnp_event_recv: recv(): Connection reset by peer

Does anyone know what the miniupnpd " Connection reset by peer" messages mean? does anything else in this log look amiss?

Thanks!

Berad

 

[VANT]

check your router temp. On this fw i have 10C lower than earlier

VANT@RT-AC87U:/tmp/home/root# cat /proc/dmu/temperature
CPU temperature : 64▒C
VANT@RT-AC87U:/tmp/home/root# qcsapi_sockrpc get_temperature
temperature_rfic_external = 0.0
temperature_rfic_internal = 57.6
temperature_bbic_internal = 55.0
VANT@RT-AC87U:/tmp/home/root#

 

[icemankent]

I did not do a reset to defaults after my upgrade and now my ddns and wireless printing are not working.
I will try a reset and reconfigure everything to see if that fixes the issues.

UPDATE:
I know, I know - the golden rule is to ALWAYS reset to factory defaults after any firmware upgrade/change - no matter what.
After I did this - and reconfigured everything - guess what (you already know the answer) - everything is working like it should.

It has been up for about 6 hours now and so far so good !

 

[gianluca1989]

In the Traffic Analyzer >> App section
the graph data of App is blank.
This is an example

 

[Embattle]

The new app currently appears not to work on Android Marsh mellow devices, fix due soon apparently.

 

[scavenger]

That app is pretty slick. There's a surprising amount of data on there I hadn't expected.

This router is finally starting to hit its potential, if only we can get MU-MIMO and the client support to go with it.

 

[sentinelvdx]

MU-MIMO is already being tested. There had been some betas including it, so we will see it soon

Sent from my SM-G920I using Tapatalk

 

[DaveMishSr]

I have done several FW updates before, but when trying to upload the newest (.9313) I get the message: "Firmware upgrade unsuccessful. This may result from incorrect image or error transmission. Please check the version of firmware and try again."
I tried several times and as well as with the FW-version on the official site as the one mentioned in the top of this thread.
Any idea?

You have 2 choices:

1) Unplug all USB devices & reboot.
2) Run the following via telnet/SSH & reboot:

nvram set drop_caches=1
nvram commit

 

[Maastricht]

You have 2 choices:

1) Unplug all USB devices & reboot.
2) Run the following via telnet/SSH & reboot:

nvram set drop_caches=1
nvram commit

Thanks, but please see post 24.
It works.

 

[Veldkornet]

iOS app coming soon.

Hmm, I wonder what "soon" is....

 

[bradbort]

In the Traffic Analyzer >> App section
the graph data of App is blank.
This is an example
View attachment 4748

It was blank at first for me too, then I clicked on apps and back to router and it popultated. Still, I think have introduced a bug.

 

[ASUS_ASUSWRT]

In the Traffic Analyzer >> App section
the graph data of App is blank.
This is an example
View attachment 4748

Will fix it soon. Thank you.

 

[sentinelvdx]

It was blank at first for me too, then I clicked on apps and back to router and it popultated. Still, I think have introduced a bug.

My case I have to wait a couple of seconds to be populated the Traffic Analyzer

Sent from my SM-G920I using Tapatalk

 

[hyungsub]

this ver. 378.9313 And old version And 380 beta version
5ghz wifi ping loss



i hope ping loss 0% ... please... ping loss ping lossping lossping loss ping loss ping loss
ping loss ping loss ping loss ping loss ping loss

 

[vanic]

Traffic analyzer issue:
You can report into this thread http://www.snbforums.com/threads/check-bug-traffic-analyzer-statistic.28098/
Thanks