x3mRouting x3mRouting ~ Selective Routing for Asuswrt-Merlin Firmware (1-Nov-2020)
- Thread starter Xentrk
- Start date
Xentrk
Part of the Furniture
x3mRouting does not place those entries in nat-start. Remove them if using x3mRouting. Or, did you create those entries for Policy Routing for ports? nat-start is creating the RPDB rules. Then, x3mRouting runs which removes the rules and updates per the x3mRouting code.
x3mRouting FWMARKS and RPDB rules
Code:
## Define interface/bitmask to route traffic to below
Set_Fwmark_Parms() {
FWMARK_WAN="0x8000/0x8000"
FWMARK_OVPNC1="0x1000/0x1000"
FWMARK_OVPNC2="0x2000/0x2000"
FWMARK_OVPNC3="0x4000/0x4000"
FWMARK_OVPNC4="0x7000/0x7000"
FWMARK_OVPNC5="0x3000/0x3000"
}
Set_IP_Rule() {
VPN_ID="$1"
case "$VPN_ID" in
0)
if [ "$(ip rule | grep -cm 1 "$TAG_MARK")" -eq 0 ]; then
ip rule add from 0/0 fwmark "$TAG_MARK" table 254 prio 9990 && logger -st "($(basename "$0"))" $$ "Created fwmark $TAG_MARK"
ip route flush cache
fi
;;
1)
if [ "$(ip rule | grep -cm 1 "$TAG_MARK")" -eq 0 ]; then
ip rule add from 0/0 fwmark "$TAG_MARK" table ovpnc1 prio 9995 && logger -st "($(basename "$0"))" $$ "Created fwmark $TAG_MARK"
ip route flush cache
fi
;;
2)
if [ "$(ip rule | grep -cm 1 "$TAG_MARK")" -eq 0 ]; then
ip rule add from 0/0 fwmark "$TAG_MARK" table ovpnc2 prio 9994 && logger -st "($(basename "$0"))" $$ "Created fwmark $TAG_MARK"
ip route flush cache
fi
;;
3)
if [ "$(ip rule | grep -cm 1 "$TAG_MARK")" -eq 0 ]; then
ip rule add from 0/0 fwmark "$TAG_MARK" table ovpnc3 prio 9993 && logger -st "($(basename "$0"))" $$ "Created fwmark $TAG_MARK"
ip route flush cache
fi
;;
4)
if [ "$(ip rule | grep -cm 1 "$TAG_MARK")" -eq 0 ]; then
ip rule add from 0/0 fwmark "$TAG_MARK" table ovpnc4 prio 9992 && logger -st "($(basename "$0"))" $$ "Created fwmark $TAG_MARK"
ip route flush cache
fi
;;
5)
if [ "$(ip rule | grep -cm 1 "$TAG_MARK")" -eq 0 ]; then
ip rule add from 0/0 fwmark "$TAG_MARK" table ovpnc5 prio 9991 && logger -st "($(basename "$0"))" $$ "Created fwmark $TAG_MARK"
ip route flush cache
fi
;;
*)
Error_Exit "ERROR $1 should be 0-WAN or 1-5=VPN"
;;
esac
}
Last edited:
Xentrk
Part of the Furniture
I just started working on adding on port routing to x3mRouting. You will have to change your nat-start code to match x3mRouting code. Alternatively, you can take advantage of x3mRouting features as follows if you have a rule to route the entire LAN to OpenVPN.
Create a dummy routing rule to bypass VPN Client 1 so the WAN fwmark gets created.
Code:
x3mRouting 1 0 DUMMY ip=172.16.0.1Create the file /jffs/scripts/x3mRouting/vpnclient1-route-up
Code:
iptables -t mangle -D PREROUTING -i br0 -m iprange --src-range 192.168.1.22 -p tcp -m multiport --sport 22,80,443 -j MARK --set-mark 0x8000/0x8000 2> /dev/null
iptables -t mangle -A PREROUTING -i br0 -m iprange --src-range 192.168.1.22 -p tcp -m multiport --sport 22,80,443 -j MARK --set-mark 0x8000/0x8000/jffs/scripts/x3mRouting/vpnclient1-route-pre-down
Code:
iptables -t mangle -D PREROUTING -i br0 -m iprange --src-range 192.168.1.22 -p tcp -m multiport --sport 22,80,443 -j MARK --set-mark 0x8000/0x8000 2> /dev/nullHello everyone !
I did spend a few hours reading many posts on this forum and I think what I need is x3mRouting but I am looking for some guidance and/or assistance. I want my whole network to be protected behind a PIA vpn using an asus AC-3100 which I have been able to successfully configured. I have also been able to create PBR in order to exclude a laptop from the VPN and send him directly to my WAN... YAY
My new Chromecast with Google TV is therefor fully behind VPN but unfortunately I need Netflix and Disney+ to go out to my WAN as my VPN provider is being blocked by both. This is where x3mRouting comes into play right ? I have been reading the documentation but I am still very confused. Sorry, I am a newb.
Goal:
My router: ASUS AC-3100 with Merlin 384.19
1. Whole network behind VPN (Already completed via Asus AC-3100 & Private Internet Access)
2. Laptop excluded by VPN (Already completed via PBR)
3. Netflix + Disney+ excluded from VPN and sent to WAN - NEED HELP
Step #1 : Do I really need a USB key to install entware ? I'm reading that it can be installed via amtm who is already installed on firmware 384.19
Step #2: SSH + sh -c "$(curl -sL https://raw.githubusercontent.com/Xentrk/x3mRouting/master/Install_x3mRouting.sh)" ?
Step #3: ?
This is where I get lost a bit.
Anyone help would be greatly appreciated. My goal is very simple.. everything behind VPN, PBR in order to exclude 1 laptop and Netflix+Displey+ excluded from VPN and sent to WAN.
MANY THANKS in advance, sorry for being new to this.
I did spend a few hours reading many posts on this forum and I think what I need is x3mRouting but I am looking for some guidance and/or assistance. I want my whole network to be protected behind a PIA vpn using an asus AC-3100 which I have been able to successfully configured. I have also been able to create PBR in order to exclude a laptop from the VPN and send him directly to my WAN... YAY
My new Chromecast with Google TV is therefor fully behind VPN but unfortunately I need Netflix and Disney+ to go out to my WAN as my VPN provider is being blocked by both. This is where x3mRouting comes into play right ? I have been reading the documentation but I am still very confused. Sorry, I am a newb.
Goal:
My router: ASUS AC-3100 with Merlin 384.19
1. Whole network behind VPN (Already completed via Asus AC-3100 & Private Internet Access)
2. Laptop excluded by VPN (Already completed via PBR)
3. Netflix + Disney+ excluded from VPN and sent to WAN - NEED HELP
Step #1 : Do I really need a USB key to install entware ? I'm reading that it can be installed via amtm who is already installed on firmware 384.19
Step #2: SSH + sh -c "$(curl -sL https://raw.githubusercontent.com/Xentrk/x3mRouting/master/Install_x3mRouting.sh)" ?
Step #3: ?
This is where I get lost a bit.
Anyone help would be greatly appreciated. My goal is very simple.. everything behind VPN, PBR in order to exclude 1 laptop and Netflix+Displey+ excluded from VPN and sent to WAN.
MANY THANKS in advance, sorry for being new to this.
Yes download the x3mRouting script option 3. It should create some files inside your router. SSH into router and look for the nat-start script. And you can copy and paste some files i have to this file or you input them manually. They should be in the original x3mRouting forum but let me know if you can't them. It looks like alot to taken on but its not too difficult once you read thru the forums.
Xentrk
Part of the Furniture
Yes, a USB is required to install entware. There are packages required by the utility in entware. You can create a routing rule for the entire LAN to use the VPN using CIDR notation 192.168.1.0/24 on the OpenVPN Client Screen. Then, use x3mRouting to create the VPN bypass rule for Netflix, Prime and Disney.Hello everyone !
I did spend a few hours reading many posts on this forum and I think what I need is x3mRouting but I am looking for some guidance and/or assistance. I want my whole network to be protected behind a PIA vpn using an asus AC-3100 which I have been able to successfully configured. I have also been able to create PBR in order to exclude a laptop from the VPN and send him directly to my WAN... YAY
My new Chromecast with Google TV is therefor fully behind VPN but unfortunately I need Netflix and Disney+ to go out to my WAN as my VPN provider is being blocked by both. This is where x3mRouting comes into play right ? I have been reading the documentation but I am still very confused. Sorry, I am a newb.
Goal:
My router: ASUS AC-3100 with Merlin 384.19
1. Whole network behind VPN (Already completed via Asus AC-3100 & Private Internet Access)
2. Laptop excluded by VPN (Already completed via PBR)
3. Netflix + Disney+ excluded from VPN and sent to WAN - NEED HELP
Step #1 : Do I really need a USB key to install entware ? I'm reading that it can be installed via amtm who is already installed on firmware 384.19
Step #2: SSH + sh -c "$(curl -sL https://raw.githubusercontent.com/Xentrk/x3mRouting/master/Install_x3mRouting.sh)" ?
Step #3: ?
This is where I get lost a bit.
Anyone help would be greatly appreciated. My goal is very simple.. everything behind VPN, PBR in order to exclude 1 laptop and Netflix+Displey+ excluded from VPN and sent to WAN.
MANY THANKS in advance, sorry for being new to this.
wolvenstein
New Around Here
I'm using Torguard with dedicated streaming IP. And x3mrouting had been working superbly. Until today, Disney+ geo-blocking my IP. Upon troubleshooting, I have to change the "Accept DNS Configuration" from strict to exclusive to make it work again. But the problem now is x3mrouting is no longer working well, as I can't route some domain to WAN. Any tips to solve this?
Sean Rhodes
Regular Contributor
How do I install x3mrouting V1.0? I have the RT3200, so 384.13_10 is the max upgrade I can go to on this router. I just did a complete wipe and reset, only to find that x3mrouting V2.40 is not compatible with my router now
Code:
Invalid firmware version detected - 384.13. This option of x3mRouting requires version 384.19 and above.
You can force update x3mRouting by typing the word 'force' below.
You must perform a 384.19+ firwmare update immediately after updating x3mRouting.Xentrk
Part of the Furniture
DNS shouldn't matter with TorGuard. Last time I checked, TG was using Cloudflare DNS.
You can try using the dnsmasq method for Disney using the code below to see if that helps.
Code:
sh /jffs/scripts/x3mRouting/x3mRouting.sh ALL 1 DISNEY dnsmasq=demdex.net,disney-plus.net,disneyplus.co,disneyplus.com,dssott.com,go.comThis is routing Disney traffic to VPN Client 1 which is my Private IP with TorGuard.
Xentrk
Part of the Furniture
I saved a compatible version in the branch on GitHub.
GitHub - Xentrk/x3mRouting at x3mRouting-384.18
Selectively route LAN clients, website or streaming media traffic over the WAN or OpenVPN client interfaces on Asuswrt-Merlin firmware - GitHub - Xentrk/x3mRouting at x3mRouting-384.18
github.com
Installation
Code:
sh -c "$(curl -sL https://raw.githubusercontent.com/Xentrk/x3mRouting/x3mRouting-384.18/Install_x3mRouting.sh)"wolvenstein
New Around Here
Works like a charm. Thanks!!
Sean Rhodes
Regular Contributor
Perfect thanks for the helpI saved a compatible version in the branch on GitHub.
GitHub - Xentrk/x3mRouting at x3mRouting-384.18
Selectively route LAN clients, website or streaming media traffic over the WAN or OpenVPN client interfaces on Asuswrt-Merlin firmware - GitHub - Xentrk/x3mRouting at x3mRouting-384.18
Installation
Code:sh -c "$(curl -sL https://raw.githubusercontent.com/Xentrk/x3mRouting/x3mRouting-384.18/Install_x3mRouting.sh)"
Xentrk
Part of the Furniture
The AWS region method using US or GLOBAL worked last time I tested it. Or, the ASN method using AS16509, which also happens to be the same ASN used by Netflix.
ASN Lookup Tool Output
Code:
# asn disneyplus.com
---------------------------------
| ASN lookup for disneyplus.com |
---------------------------------
- Resolving "disneyplus.com"... 1 IP address found:
54.71.61.241 +PTR ec2-54-71-61-241.us-west-2.compute.amazonaws.com
+ASN 16509 (AMAZON-02, US)
+ORG Amazon.com, Inc.
+NET 54.70.0.0/15 (AMAZON-2011L)
+ABU abuse@amazonaws.com
+GEO Portland, Oregon (US)
<snip>
Code:
# asn netflix.com
------------------------------
| ASN lookup for netflix.com |
------------------------------
- Resolving "netflix.com"... 8 IP addresses found:
52.18.96.227 +PTR ec2-52-18-96-227.eu-west-1.compute.amazonaws.com
+ASN 16509 (AMAZON-02, US)
+ORG Amazon.com, Inc.
+NET 52.18.0.0/15 (AMAZON-DUB)
+ABU abuse@amazonaws.com
+GEO Dublin, Dublin (IE)Sean Rhodes
Regular Contributor
Xentrk, I followed the numerous posts between you and Rappy back in 2017 and found those invaluable. I have the BBC iPlayer working fine on my AppleTV now, I have to re-run the script again each day before using, otherwise the ATV comes up with a blank screen, but once run it works fine. I have 3 main questions.
1. Is it better to use domain names to lessen the chance of IP changes vs using say an IPSET of all the BBC IP's?
2. Is the VPN Gui update available in FW 384.13 to try out option 2?
3. The VPN stays up the whole time, so why would I have to re-run the script again?
1. Is it better to use domain names to lessen the chance of IP changes vs using say an IPSET of all the BBC IP's?
2. Is the VPN Gui update available in FW 384.13 to try out option 2?
3. The VPN stays up the whole time, so why would I have to re-run the script again?
Last edited:
Xentrk
Part of the Furniture
I learned a lot since that conversation.
This is the latest iteration that works for BBC using the dnsmasq method.
Code:
sh /jffs/scripts/x3mRouting/x3mRouting.sh ALL 3 BBC_WEB dnsmasq=bbc.co.uk,bbc.com,bbc.gscontxt.net,bbci.co.uk,bbctvapps.co.uk,ssl-bbcsmarttv.2cnt.netSee if this solves your issues first before trying other solutions. I tested on iPlayer app on iPad, Firefox on Win10 and FireTV. You shouldn't have to rerun the script.
The issue with the GUI is I have to keep it current with the firmware versions are they are released. Best to stay away from using the GUI if you don't intend to stay current with the firmware releases.
Sean Rhodes
Regular Contributor
Thanks for all the help, I will try tonight and see how it goes
Similar threads
Similar threads
Similar threads
-
How do I get x3mrouting working with AdGuard Home ?
- Started by ComputerSteve
- Replies: 6
-
x3mRouting x3mRouting vs Domain based VPN routing
- Started by Armandooooo
- Replies: 29
-
DomainVPNRouting Domain VPN Routing v3.0.4 ***Release***
- Started by Ranger802004
- Replies: 54
-
Question about DomainBased Routing & Re-connection
- Started by ComputerSteve
- Replies: 0
-
-
DomainVPNRouting Domain VPN Routing Question
- Started by Armandooooo
- Replies: 32
-
DomainVPNRouting Domain-based VPN routing script
- Started by johndoe85
- Replies: 2
-