modmon modmon - WebUI for monitoring Virgin Hub 3 cable modem stats

[Jack Yaz]

@Jack Yaz

I have an Arris SURFboard SB6183 and my status page is at http://192.168.100.1/RgConnect.asp or if I simply type the address 192.168.100.1. Can this somehow work for me?

View attachment 22814

Load the page with the network section of Chrome's dev console open, see how it is requesting the data

 

[bluzfanmr1]

Load the page with the network section of Chrome's dev console open, see how it is requesting the data

I use Safari and know how to open the console but I'm unsure what info you need?

 

[Jack Yaz]

I use Safari and know how to open the console but I'm unsure what info you need?

A screenshot of all the loaded resources from network would be a good place to start please. On my Hub 3.0 I saw the stats page making a call to getRouterStatus which is what I hooked into

 

[bluzfanmr1]

A screenshot of all the loaded resources from network would be a good place to start please. On my Hub 3.0 I saw the stats page making a call to getRouterStatus which is what I hooked into

Hope this is the right thing...

 

[Jack Yaz]

Hope this is the right thing...

View attachment 22816

Hm so it must be doing it in the page...that makes it trickier

 

[Jack Yaz]

much faster when set to average, also the charts look cleaner, e.g.
average:
View attachment 22765

raw:
View attachment 22766

Would you be willing to test load times on the develop branch please? I suspect it will take a similar amount of time, but loading is done chart by chart rather than all in 1 go

 

[JonEngland]

Would you be willing to test load times on the develop branch please? I suspect it will take a similar amount of time, but loading is done chart by chart rather than all in 1 go

sure, what's the install command?

 

[Jack Yaz]

sure, what's the install command?

modmon develop

should do the trick!

 

[JonEngland]

modmon develop

should do the trick!

a message flashed up, possibly an error but I didn't catch it and the usual modmon menu displayed (v1.0.0)
I tested time to show charts, results below:

average: 2s
raw: 17s​

If I retry the command I get this

# modmon develop
sed: can't move '/jffs/scripts/kMbJd9' to '/jffs/scripts/': Not a directory
modmon: No new version - latest is v1.0.0

 

[Jack Yaz]

a message flashed up, possibly an error but I didn't catch it and the usual modmon menu displayed (v1.0.0)
I tested time to show charts, results below:

average: 2s
raw: 17s​

If I retry the command I get this

# modmon develop
sed: can't move '/jffs/scripts/kMbJd9' to '/jffs/scripts/': Not a directory
modmon: No new version - latest is v1.0.0

Weird, try swapping back with "stable" and then back to develop please

 

[JonEngland]

Weird, try swapping back with "stable" and then back to develop please

modmon stable
sed: can't move '/jffs/scripts/0aOH0a' to '/jffs/scripts/': Not a directory
modmon: No new version - latest is v1.0.0

it returns to prompt and doesn't load modmon
running just modmon works ok

 

[Jack Yaz]

modmon stable
sed: can't move '/jffs/scripts/0aOH0a' to '/jffs/scripts/': Not a directory
modmon: No new version - latest is v1.0.0

it returns to prompt and doesn't load modmon
running just modmon works ok

Hm so sed is failing to edit the file. Check if modmon is stuck running in ps?

 

[JonEngland]

Hm so sed is failing to edit the file. Check if modmon is stuck running in ps?

I don't see modmon running

# ps |grep modmon
24339 ac86u     5432 R    grep modmon
# modmon stable
sed: can't move '/jffs/scripts/sPYRP0' to '/jffs/scripts/': Not a directory
modmon: No new version - latest is v1.0.0
# ps |grep modmon
24439 ac86u     5432 S    grep modmon

 

[Wisiwyg]

It requires your router to be able to access the IP address of your cable modem

Note not all Status pages load from the same URL... here it is Index, SurfBoard SB6141

 

[Wisiwyg]

Hm. Anything that shows a breakdown of power levels and snr etc. per channel?

Located under the Signal tab at http://192.168.100.1/cmSignal.htm.

Arris SB6141 cable modem, Comcast provider.

 

[SMS786]

@Jack Yaz Does this help at all? Arris SB6183 here..

 

[chewmull]

I have an Arris SB-6141 and when I go to install it tells me the modems not supported. Are there only particular Arris model that work with this?

 

[sentinelvdx]

@Jack Yaz I use this URL to get my signal levels without login into my modem... do you think it might work with your script?
In Argentina with ISP "Fibertel" it's an easy way to check the signal no matter which modem we are using.

http://www.dameunaip.com.ar/asp/nivelesPrima.asp

Using S.G.S9+ Duos w/ Tapatalk

 

[Kingp1n]

Doubt this would work on a Netgear modem, correct?

 

[Jack Yaz]

v1.0.1 is now available
Changelog:

CHANGED: Improved loading mechanism for charts