Beta Asuswrt-Merlin 3006.102.3 beta is now available for Wifi 7 devices

[fryedchikin]

GT-BE98 Pro updated from 3006_102.2_2
Wireless Log is not showing clients connected to the 5 GHz band. They are being correctly reported for the 2.4 GHz, 6 GHz-1 and 6 GHz-2 bands

Low level details shows the 3 connected clients I would expect to see.

 

[Mutzli]

GT-BE98 Pro updated from 3006_102.2_2
Wireless Log is not showing clients connected to the 5 GHz band. They are being correctly reported for the 2.4 GHz, 6 GHz-1 and 6 GHz-2 bands

Low level details shows the 3 connected clients I would expect to see.
View attachment 63253
View attachment 63252

How long did you keep this page open? Sometimes it takes a few minutes to tabulate this log.

 

[fryedchikin]

How long did you keep this page open? Sometimes it takes a few minutes to tabulate this log.

I did leave it open for quite a while I was troubleshooting, connecting and disconnecting clients to the 5Ghz SSID.

Changes were listed relating to this page and this is the first time I have seen it occur, so thought I would mention it. I may just reboot later and see what happens.

 

[RogerSC]

Flashed this several days ago, and it's doing great. MLO is working well, clients that support 6GHz. are put there if appropriate. Wireless is strong and reliable. No problems at this point, very happy with this firmware. A few odd messages in the system log, but they're apparently debugging information for Asus, since there are no problems in operation.

Thanks, Merlin!

 

[nomadneo]

Flashed this several days ago, and it's doing great. MLO is working well, clients that support 6GHz. are put there if appropriate. Wireless is strong and reliable. No problems at this point, very happy with this firmware. A few odd messages in the system log, but they're apparently debugging information for Asus, since there are no problems in operation.

Thanks, Merlin!

Did you flash over wifi or a wire?

 

[RogerSC]

Did you flash over wifi or a wire?

Downloaded the image and checksummed it. Then flashed it from the desktop on my cable-connected desktop computer. So that would be "over a wire".

 

[RMerlin]

Did you flash over wifi or a wire?

Makes no difference. If the file fails to transfers properly, then it won't flash at all - the image is validated before being written to flash.

 

[Krism]

currently running for approx 4h on my RT-be88u and no issues so far.

 

[_Harald_]

Rt-BE-86U.. upgraded from previous merllin release.. run several days with this beta release and findings were..
- LAN1 port dropped to 100M mode after reboot.. LAN cable out of plug for a 10 seconds or more and plugged back, 1G connection restored. After few hours or maybe day, LAN1 dropped to 100M mode
- seriours WiFi problems ith wifi 7 enabled devices.. slow connetions or no connectivity at all
- Citrix problems.. citrix teams calls very sluggish - very bad call quality, desktops sharing problems
- extremely sluggish router's web interface use
- probs with Scribe installation.. this was solved earlier within this tread.
Upgraded from previous merlin release.. similar problems present there as well. I'm using Diversion and Skynet as this is main reason to have merlin based sw in a first place..

"Downgrade" to Asus official latest release and overall no above mentioned problems at all.. ok, sometimes I hve a feeling of sluggish router interface but this is fairly seldom..

 

[RMerlin]

GT-BE98 Pro updated from 3006_102.2_2
Wireless Log is not showing clients connected to the 5 GHz band. They are being correctly reported for the 2.4 GHz, 6 GHz-1 and 6 GHz-2 bands

Low level details shows the 3 connected clients I would expect to see.
View attachment 63253
View attachment 63252

Works for me.

Anyone else with a GT-BE98_PRO?

 

[QuikSilver]

Works for me.

Anyone else with a GT-BE98_PRO?

It retails for over $600.

 

[Blacklistedcard]

Works for me.

Anyone else with a GT-BE98_PRO?

Confirming I don't have that problem on my BE98 Pro.

 

[nzwayne]

Works for me.

Anyone else with a GT-BE98_PRO?

On Beta1, I have the expected clients connected on LAN, 2.4/5/6GHz.

 

[visortgw]

Works for me.

Anyone else with a GT-BE98_PRO?

Works for me as well.

 

[xTerminator]

Dumb question, just to double check. I am on stock firmware 3.0.0.6.102_37103 RT-BE88U. If I set DOWNGRADE_CHECK_PASS and flash this beta, I do not need to do factory reset settings ? Factory reset is only needed to reset settings if I downgrade to lets say 3006.102.1 right.

 

[RMerlin]

Dumb question, just to double check. I am on stock firmware 3.0.0.6.102_37103 RT-BE88U. If I set DOWNGRADE_CHECK_PASS and flash this beta, I do not need to do factory reset settings ? Factory reset is only needed to reset settings if I downgrade to lets say 3006.102.1 right.

Resetting following a switch from stock to Asuswrt-Merlin is generally not required, but strongly recommended if you do have anything VPN-related configured under the stock firmware - both firmware have different OpenVPN settings.

 

[emwgee]

Works for me.

Anyone else with a GT-BE98_PRO?

After updated to beta_1 on my GT-BE98 PRO from 3006_102.2_2, wireless log shows only two of my three 2.4GHz guest networks, even though the unshown network is there and working fine with clients connected to it.

I tried refreshing wireless log, cleared browser cache, disabled and re-enable the unshown network and reboot the router. None of that helps.

 

[fryedchikin]

Works for me.

Anyone else with a GT-BE98_PRO?

Thanks for checking. The issue persists after reboots so if there is any data I can gather to help solve the mystery please let me know what you need. I should have time to try a factory reset this weekend if needed. As of now I have 4 connected clients to 5GHz and only one showing. I have not seen any issues with actual connectivity so just a cosmetic anomaly. 2.4, 6-1 and 6-2 are still showing everything just fine.

 

[cljackhammer]

Unable to set a VLAN ID for a MLO network. I don’t see the option available. Not sure if this impacts any other types of networks.

 

[cljackhammer]

Unable to set a VLAN ID for a MLO network. I don’t see the option available. Not sure if this impacts any other types of networks.

Disregard @Merlin. User error.