Asuswrt-Merlin 380.59 is now available

L&LD · Jun 13, 2016

Ramjattan said:
I did a factory reset and all settings left on default. When I flashed firmware 380.59 thats when the 5ghz led stopped staying on after a reboot but the 5ghz WiFi is working if I flash a older firmware like the last one the led would stay on after a reboot it's like some setting is not serveing the reboot or not serveing thank you for your reply sir

The order of operations is:

Flash new firmware to the unit.
Perform a reset to factory defaults.

http://www.snbforums.com/threads/no...l-and-manual-configuration.27115/#post-205573

RMerlin · Jun 13, 2016

Resike said:
380.59 drops media streaming services after a while. 380.58 does not have this issue.

Try the 380.60 alpha 3 beta if your model is supported. It includes changes to minidlna related to broadcasts.

Henk59 · Jun 15, 2016

"Routing conflict error" warning is back in this release, it was solved in 380.58,
if I switch OpenVPN (Client) On/Off with IPVanish.

Hope it will be gone in .60 version.

RMerlin · Jun 15, 2016

Folks with SMB connectivity issues, try the following smb.postconf:

Code:

#!/bin/sh
CONFIG=$1
source /usr/sbin/helper.sh

pc_insert "[global]" "client use spnego = no" $CONFIG

Windows 7 + Windows Live Essentials tend to mess up with SMB authentication. I thought the issue had been resolved in Samba 3.5.6, but it's possible that it could still be problematic. This would disable the incompatible handshaking support.

xus · Jun 16, 2016

sometimes when I click traffic analyser my whole GUI seems to fail, even trying to access login page from another device it just loads forever. requires a reboot to sort, anyone else seen this happening? ac68u.

when this happens no traffic data is logged but internet remains up for all devices

terribell · Jun 19, 2016

Just upgraded from an RT-N66U to an RT-AC68U HW REV A2 with this firmware 380.59 and been having troubles with an external hard disk.
I've tried with the option "Reducing USB 3.0 interference" enabled and disabled and also connecting the hard disk to the USB 2.0 port but he stops responding to samba requests and also to DLNA requests.

The log when I plug the router and access the Samba I get the following log:
"Jun 19 12:23:30 kernel: usb 1-1: new SuperSpeed USB device using xhci_hcd and address 2
Jun 19 12:23:30 kernel: xhci_hcd 0000:00:0c.0: WARN: short transfer on control ep
Jun 19 12:23:30 kernel: xhci_hcd 0000:00:0c.0: WARN: short transfer on control ep
Jun 19 12:23:30 kernel: xhci_hcd 0000:00:0c.0: WARN: short transfer on control ep
Jun 19 12:23:30 kernel: xhci_hcd 0000:00:0c.0: WARN: short transfer on control ep
Jun 19 12:23:30 kernel: xhci_hcd 0000:00:0c.0: disable burst on ep 1
Jun 19 12:23:30 kernel: xhci_hcd 0000:00:0c.0: WARN no SS endpoint bMaxBurst
Jun 19 12:23:30 kernel: xhci_hcd 0000:00:0c.0: disable burst on ep 2
Jun 19 12:23:30 kernel: xhci_hcd 0000:00:0c.0: WARN no SS endpoint bMaxBurst
Jun 19 12:23:30 kernel: scsi0 : usb-storage 1-1:1.0
Jun 19 12:23:31 kernel: scsi 0:0:0:0: Direct-Access ST3000DM 001-1CH166 CC47 PQ: 0 ANSI: 6
Jun 19 12:23:31 kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0
Jun 19 12:23:31 kernel: sd 0:0:0:0: [sda] Very big device. Trying to use READ CAPACITY(16).
Jun 19 12:23:31 kernel: xhci_hcd 0000:00:0c.0: WARN: Stalled endpoint
Jun 19 12:23:31 kernel: sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
Jun 19 12:23:31 kernel: xhci_hcd 0000:00:0c.0: WARN: Stalled endpoint
Jun 19 12:23:31 kernel: sd 0:0:0:0: [sda] Write Protect is off
Jun 19 12:23:31 kernel: sd 0:0:0:0: [sda] Assuming drive cache: write through
Jun 19 12:23:31 kernel: sd 0:0:0:0: [sda] Very big device. Trying to use READ CAPACITY(16).
Jun 19 12:23:31 kernel: xhci_hcd 0000:00:0c.0: WARN: Stalled endpoint
Jun 19 12:23:31 kernel: xhci_hcd 0000:00:0c.0: WARN: Stalled endpoint
Jun 19 12:23:31 kernel: sd 0:0:0:0: [sda] Assuming drive cache: write through
Jun 19 12:23:31 kernel: sda: sda1 sda2
Jun 19 12:23:31 kernel: sd 0:0:0:0: [sda] Very big device. Trying to use READ CAPACITY(16).
Jun 19 12:23:31 kernel: xhci_hcd 0000:00:0c.0: WARN: Stalled endpoint
Jun 19 12:23:31 kernel: xhci_hcd 0000:00:0c.0: WARN: Stalled endpoint
Jun 19 12:23:31 kernel: sd 0:0:0:0: [sda] Assuming drive cache: write through
Jun 19 12:23:31 kernel: sd 0:0:0:0: [sda] Attached SCSI disk
Jun 19 12:23:31 hotplug[1301]: USB /dev/sda1(unknown) failed to mount at the first try!
Jun 19 12:23:31 usb: USB /dev/sda1(unknown) failed to mount At the first try!
Jun 19 12:23:31 kernel: tfat: fail_safe is enabled
Jun 19 12:23:31 kernel: tntfs info (device sda1, pid 1310): ntfs_fill_super(): fail_safe is enabled
Jun 19 12:23:32 hotplug[1299]: USB /dev/sda2(ntfs) failed to mount at the first try!
Jun 19 12:23:32 usb: USB /dev/sda2(ntfs) failed to mount At the first try!
Jun 19 12:23:32 kernel: tntfs info (device sda2, pid 1334): ntfs_fill_super(): fail_safe is enabled
Jun 19 12:23:32 kernel: tntfs info (device sda2, pid 1334): load_system_files(): NTFS volume name 'Verbatim HDD', version 3.1 (cluster_size 4096, PAGE_CACHE_SIZE 4096).
Jun 19 12:23:33 syslog: USB ntfs fs at /dev/sda2 mounted on /tmp/mnt/Verbatim_HDD
Jun 19 12:23:33 usb: USB ntfs fs at /dev/sda2 mounted on /tmp/mnt/Verbatim_HDD.
Jun 19 12:23:33 rc_service: hotplug 1299:notify_rc restart_nasapps
Jun 19 12:23:34 iTunes: daemon is stopped
Jun 19 12:23:34 FTP Server: daemon is stopped
Jun 19 12:23:34 Samba Server: smb daemon is stopped
Jun 19 12:23:34 kernel: gro disabled
Jun 19 12:23:35 Timemachine: daemon is stopped
Jun 19 12:23:35 miniupnpd[720]: shutting down MiniUPnPd
Jun 19 12:23:35 kernel: gro enabled with interval 2
Jun 19 12:23:37 Samba Server: daemon is started
Jun 19 12:23:37 kernel: RPC: Registered udp transport module.
Jun 19 12:23:37 kernel: RPC: Registered tcp transport module.
Jun 19 12:23:37 kernel: RPC: Registered tcp NFSv4.1 backchannel transport module.
Jun 19 12:23:37 kernel: Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Jun 19 12:23:37 statd[1387]: Version 1.1.6 Starting
Jun 19 12:23:37 statd[1387]: statd running as root. chown /var/lib/nfs/sm to choose different user
Jun 19 12:23:37 kernel: svc: failed to register lockdv1 RPC service (errno 97).
Jun 19 12:23:39 miniupnpd[1402]: HTTP listening on port 35966
Jun 19 12:23:39 miniupnpd[1402]: Listening for NAT-PMP/PCP traffic on port 5351

Jun 19 12:24:58 kernel: __find_get_block_slow() failed. block=5517221896, b_blocknr=1222254600
Jun 19 12:24:58 kernel: b_state=0x00000020, b_size=512
Jun 19 12:24:58 kernel: device blocksize: 512
Jun 19 12:24:58 kernel: __find_get_block_slow() failed. block=5517221896, b_blocknr=1222254600
Jun 19 12:24:58 kernel: b_state=0x00000020, b_size=512
Jun 19 12:24:58 kernel: device blocksize: 512"

This last part with of kernel log repeats itself lots of time when we try to access samba.

On the top activity I get samba consuming the bigger part of CPU:

Mem: 102552K used, 153148K free, 0K shrd, 1080K buff, 40400K cached
CPU: 2.2% usr 50.6% sys 0.0% nic 46.1% idle 0.0% io 0.0% irq 0.8% sirq
Load average: 4.01 3.15 1.89 3/105 2616
PID PPID USER STAT VSZ %VSZ CPU %CPU COMMAND
1486 1374 nobody R 5976 2.3 1 22.9 /usr/sbin/smbd -D -s /etc/smb.conf
1733 1374 nobody R 5972 2.3 1 22.9 /usr/sbin/smbd -D -s /etc/smb.conf
282 2 admin SW 0 0.0 1 3.9 [kworker/1:1]
355 1 admin S 1384 0.5 0 0.7 /sbin/klogd -c 5
449 1 admin S 6568 2.5 0 0.2 httpd -i br0
742 741 admin S 2032 0.7 0 0.2 wred -B

When checking on the GUI the CPU 2 is at 100% and when I try to access samba again it says on windows explorer that "Insuficient resources exist to complete the requested service".
After this happens the router gets very slow and after a short while it hangs and stops responding to requests from wired and wireless connections.

I also get the following error on dlna log:
"[2016/06/16 07:47:37] scanner.c:615: error: Error creating SQLite3 database!
[2016/06/16 07:47:37] minidlna.c:385: fatal: ERROR: Failed to create sqlite database! Exiting...
[2016/06/19 12:23:41] minidlna.c:1205: warn: Starting MiniDLNA version 1.1.5.
[2016/06/19 12:23:42] minidlna.c:363: warn: Creating new database at /tmp/mnt/Verbatim_HDD/.minidlna/files.db
[2016/06/19 12:23:42] sql.c:41: error: SQL ERROR 1 [table OBJECTS already exists]
CREATE TABLE OBJECTS (ID INTEGER PRIMARY KEY AUTOINCREMENT, OBJECT_ID TEXT UNIQUE NOT NULL, PARENT_ID TEXT NOT NULL, REF_ID TEXT DEFAULT NULL, CLASS TEXT NOT NULL, DETAIL_ID INTEGER DEFAULT NULL, NAME TEXT DEFAULT NULL);
[2016/06/19 12:23:42] scanner.c:615: error: Error creating SQLite3 database!
[2016/06/19 12:23:42] minidlna.c:385: fatal: ERROR: Failed to create sqlite database! Exiting..."

This is very strange as this disk has been working perfectly on the RT-N66U with John's fork for some years.

Can anyone help?

terribell · Jun 19, 2016

I just wanted to add that the disk that gives problems is a 3TB 3.5" USB3.0 Seagate formated with NTFS and I've tried several USB memory sticks formated with FAT32 without any problems.

Mugur · Jun 19, 2016

Can someone please tell me if you have encountered any DDNS registering error (asuscomm.com) after .59?
Thank you.

mgeoffriau · Jun 19, 2016

Mugur said:
Can someone please tell me if you have encountered any DDNS registering error (asuscomm.com) after .59?
Thank you.

Nope, not at all. I just upgraded from an RT-N66U (380.58) to an RT-AC68R (380.59). I renamed my asuscomm DDNS on the old router, made sure it registered successfully, then logged into the new router and registered my original address. Took less than 10 seconds.

Mugur · Jun 19, 2016

I get: request error. please try again...

I am not changing routers, just new firmware and when i try to register DDNS i get that error.
Even if i try with a totally new and different name.

RMerlin · Jun 19, 2016

Mugur said:
I get: request error. please try again...

I am not changing routers, just new firmware and when i try to register DDNS i get that error.
Even if i try with a totally new and different name.

Asus's DDNS service is frequently down. I recommend switching to a different DDNS provider.

terribell · Jun 19, 2016

terribell said:
Just upgraded from an RT-N66U to an RT-AC68U HW REV A2 with this firmware 380.59 and been having troubles with an external hard disk.
I've tried with the option "Reducing USB 3.0 interference" enabled and disabled and also connecting the hard disk to the USB 2.0 port but he stops responding to samba requests and also to DLNA requests.

The log when I plug the router and access the Samba I get the following log:
"Jun 19 12:23:30 kernel: usb 1-1: new SuperSpeed USB device using xhci_hcd and address 2
Jun 19 12:23:30 kernel: xhci_hcd 0000:00:0c.0: WARN: short transfer on control ep
Jun 19 12:23:30 kernel: xhci_hcd 0000:00:0c.0: WARN: short transfer on control ep
Jun 19 12:23:30 kernel: xhci_hcd 0000:00:0c.0: WARN: short transfer on control ep
Jun 19 12:23:30 kernel: xhci_hcd 0000:00:0c.0: WARN: short transfer on control ep
Jun 19 12:23:30 kernel: xhci_hcd 0000:00:0c.0: disable burst on ep 1
Jun 19 12:23:30 kernel: xhci_hcd 0000:00:0c.0: WARN no SS endpoint bMaxBurst
Jun 19 12:23:30 kernel: xhci_hcd 0000:00:0c.0: disable burst on ep 2
Jun 19 12:23:30 kernel: xhci_hcd 0000:00:0c.0: WARN no SS endpoint bMaxBurst
Jun 19 12:23:30 kernel: scsi0 : usb-storage 1-1:1.0
Jun 19 12:23:31 kernel: scsi 0:0:0:0: Direct-Access ST3000DM 001-1CH166 CC47 PQ: 0 ANSI: 6
Jun 19 12:23:31 kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0
Jun 19 12:23:31 kernel: sd 0:0:0:0: [sda] Very big device. Trying to use READ CAPACITY(16).
Jun 19 12:23:31 kernel: xhci_hcd 0000:00:0c.0: WARN: Stalled endpoint
Jun 19 12:23:31 kernel: sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
Jun 19 12:23:31 kernel: xhci_hcd 0000:00:0c.0: WARN: Stalled endpoint
Jun 19 12:23:31 kernel: sd 0:0:0:0: [sda] Write Protect is off
Jun 19 12:23:31 kernel: sd 0:0:0:0: [sda] Assuming drive cache: write through
Jun 19 12:23:31 kernel: sd 0:0:0:0: [sda] Very big device. Trying to use READ CAPACITY(16).
Jun 19 12:23:31 kernel: xhci_hcd 0000:00:0c.0: WARN: Stalled endpoint
Jun 19 12:23:31 kernel: xhci_hcd 0000:00:0c.0: WARN: Stalled endpoint
Jun 19 12:23:31 kernel: sd 0:0:0:0: [sda] Assuming drive cache: write through
Jun 19 12:23:31 kernel: sda: sda1 sda2
Jun 19 12:23:31 kernel: sd 0:0:0:0: [sda] Very big device. Trying to use READ CAPACITY(16).
Jun 19 12:23:31 kernel: xhci_hcd 0000:00:0c.0: WARN: Stalled endpoint
Jun 19 12:23:31 kernel: xhci_hcd 0000:00:0c.0: WARN: Stalled endpoint
Jun 19 12:23:31 kernel: sd 0:0:0:0: [sda] Assuming drive cache: write through
Jun 19 12:23:31 kernel: sd 0:0:0:0: [sda] Attached SCSI disk
Jun 19 12:23:31 hotplug[1301]: USB /dev/sda1(unknown) failed to mount at the first try!
Jun 19 12:23:31 usb: USB /dev/sda1(unknown) failed to mount At the first try!
Jun 19 12:23:31 kernel: tfat: fail_safe is enabled
Jun 19 12:23:31 kernel: tntfs info (device sda1, pid 1310): ntfs_fill_super(): fail_safe is enabled
Jun 19 12:23:32 hotplug[1299]: USB /dev/sda2(ntfs) failed to mount at the first try!
Jun 19 12:23:32 usb: USB /dev/sda2(ntfs) failed to mount At the first try!
Jun 19 12:23:32 kernel: tntfs info (device sda2, pid 1334): ntfs_fill_super(): fail_safe is enabled
Jun 19 12:23:32 kernel: tntfs info (device sda2, pid 1334): load_system_files(): NTFS volume name 'Verbatim HDD', version 3.1 (cluster_size 4096, PAGE_CACHE_SIZE 4096).
Jun 19 12:23:33 syslog: USB ntfs fs at /dev/sda2 mounted on /tmp/mnt/Verbatim_HDD
Jun 19 12:23:33 usb: USB ntfs fs at /dev/sda2 mounted on /tmp/mnt/Verbatim_HDD.
Jun 19 12:23:33 rc_service: hotplug 1299:notify_rc restart_nasapps
Jun 19 12:23:34 iTunes: daemon is stopped
Jun 19 12:23:34 FTP Server: daemon is stopped
Jun 19 12:23:34 Samba Server: smb daemon is stopped
Jun 19 12:23:34 kernel: gro disabled
Jun 19 12:23:35 Timemachine: daemon is stopped
Jun 19 12:23:35 miniupnpd[720]: shutting down MiniUPnPd
Jun 19 12:23:35 kernel: gro enabled with interval 2
Jun 19 12:23:37 Samba Server: daemon is started
Jun 19 12:23:37 kernel: RPC: Registered udp transport module.
Jun 19 12:23:37 kernel: RPC: Registered tcp transport module.
Jun 19 12:23:37 kernel: RPC: Registered tcp NFSv4.1 backchannel transport module.
Jun 19 12:23:37 kernel: Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Jun 19 12:23:37 statd[1387]: Version 1.1.6 Starting
Jun 19 12:23:37 statd[1387]: statd running as root. chown /var/lib/nfs/sm to choose different user
Jun 19 12:23:37 kernel: svc: failed to register lockdv1 RPC service (errno 97).
Jun 19 12:23:39 miniupnpd[1402]: HTTP listening on port 35966
Jun 19 12:23:39 miniupnpd[1402]: Listening for NAT-PMP/PCP traffic on port 5351

Jun 19 12:24:58 kernel: __find_get_block_slow() failed. block=5517221896, b_blocknr=1222254600
Jun 19 12:24:58 kernel: b_state=0x00000020, b_size=512
Jun 19 12:24:58 kernel: device blocksize: 512
Jun 19 12:24:58 kernel: __find_get_block_slow() failed. block=5517221896, b_blocknr=1222254600
Jun 19 12:24:58 kernel: b_state=0x00000020, b_size=512
Jun 19 12:24:58 kernel: device blocksize: 512"

This last part with of kernel log repeats itself lots of time when we try to access samba.

On the top activity I get samba consuming the bigger part of CPU:

Mem: 102552K used, 153148K free, 0K shrd, 1080K buff, 40400K cached
CPU: 2.2% usr 50.6% sys 0.0% nic 46.1% idle 0.0% io 0.0% irq 0.8% sirq
Load average: 4.01 3.15 1.89 3/105 2616
PID PPID USER STAT VSZ %VSZ CPU %CPU COMMAND
1486 1374 nobody R 5976 2.3 1 22.9 /usr/sbin/smbd -D -s /etc/smb.conf
1733 1374 nobody R 5972 2.3 1 22.9 /usr/sbin/smbd -D -s /etc/smb.conf
282 2 admin SW 0 0.0 1 3.9 [kworker/1:1]
355 1 admin S 1384 0.5 0 0.7 /sbin/klogd -c 5
449 1 admin S 6568 2.5 0 0.2 httpd -i br0
742 741 admin S 2032 0.7 0 0.2 wred -B

When checking on the GUI the CPU 2 is at 100% and when I try to access samba again it says on windows explorer that "Insuficient resources exist to complete the requested service".
After this happens the router gets very slow and after a short while it hangs and stops responding to requests from wired and wireless connections.

I also get the following error on dlna log:
"[2016/06/16 07:47:37] scanner.c:615: error: Error creating SQLite3 database!
[2016/06/16 07:47:37] minidlna.c:385: fatal: ERROR: Failed to create sqlite database! Exiting...
[2016/06/19 12:23:41] minidlna.c:1205: warn: Starting MiniDLNA version 1.1.5.
[2016/06/19 12:23:42] minidlna.c:363: warn: Creating new database at /tmp/mnt/Verbatim_HDD/.minidlna/files.db
[2016/06/19 12:23:42] sql.c:41: error: SQL ERROR 1 [table OBJECTS already exists]
CREATE TABLE OBJECTS (ID INTEGER PRIMARY KEY AUTOINCREMENT, OBJECT_ID TEXT UNIQUE NOT NULL, PARENT_ID TEXT NOT NULL, REF_ID TEXT DEFAULT NULL, CLASS TEXT NOT NULL, DETAIL_ID INTEGER DEFAULT NULL, NAME TEXT DEFAULT NULL);
[2016/06/19 12:23:42] scanner.c:615: error: Error creating SQLite3 database!
[2016/06/19 12:23:42] minidlna.c:385: fatal: ERROR: Failed to create sqlite database! Exiting..."

This is very strange as this disk has been working perfectly on the RT-N66U with John's fork for some years.

Can anyone help?

@RMerlin

Any idea on this problem??

Mugur · Jun 20, 2016

@RMerlin
Sorry to bother you again. Any other idea to try on the DDNS issue with 87U? I have logged from the same internet connection using my RT-68U and the asus server responds instantly. When i am trying from 87U it says "applying settings" and stays there forever. Once i reload the page the answer is "request error. please try again later"

RMerlin · Jun 20, 2016

Mugur said:
@RMerlin
Sorry to bother you again. Any other idea to try on the DDNS issue with 87U? I have logged from the same internet connection using my RT-68U and the asus server responds instantly. When i am trying from 87U it says "applying settings" and stays there forever. Once i reload the page the answer is "request error. please try again later"

As I said, try a different DDNS service provider.

Darunia · Jun 20, 2016

For the past couple of weeks the Network Map wasn't loading all of a sudden. I go to Tools > Sysinfo, go down to Ethernet Ports and find this message: 'Querying switch...' Everything plugged into the Ethernet ports and the router itself works fine otherwise. There's days where it queries the switch fine and shows what's plugged in along with the Network Map like normal, other times it goes back to that message. Any ideas what's going on?

RMerlin · Jun 20, 2016

Darunia said:
For the past couple of weeks the Network Map wasn't loading all of a sudden. I go to Tools > Sysinfo, go down to Ethernet Ports and find this message: 'Querying switch...' Everything plugged into the Ethernet ports and the router itself works fine otherwise. There's days where it queries the switch fine and shows what's plugged in along with the Network Map like normal, other times it goes back to that message. Any ideas on what's going on?

You have a device with an invalid name causing Javascript errors. Open your web browser console, and look at the line containing the error - it should tell you what device name is breaking it. Typically, it's caused by devices with quotes in their names.

Darunia · Jun 21, 2016

Thing is, I've been using the same names for the past year and a half I've had this router without issue until now, initially with stock firmware and from 378.51 to 380.59. There's 3 names that use apostrophes but that's it.

RMerlin · Jun 21, 2016

Darunia said:
Thing is, I've been using the same names for the past year and a half I've had this router without issue until now, initially with stock firmware and from 378.51 to 380.59. There's 3 names that use apostrophes but that's it.

Remove the apostrophes.

XIII · Jun 21, 2016

I might have just missed this before, but my AC66U is dropping the 2.4Ghz band with 380.59. I notice(d) it now because my Philips Fidelio speakers are unable to connect to my home network (these don't work on the 5 Ghz band which is still available for my iPhone and iPad). My current workaround is to reboot the router.

What else can I do or should I try?

XIII · Jun 21, 2016

I also just noticed this:

wl0_country_code=EU
wl_country_code=US
wl1_country_code=EU

I have never tinkered with these settings and I have no intention to, as I want to make sure that I follow the appropriate (EU) laws. However, the set currently seems inconsistent to me. Should the "wl_country_code" not also be "EU" instead of "US"? If so, (how) can I (safely) change that?

Also weird: OS X El Capitan's Wireless Diagnostics lists the country as FR while I don't live in France.

Thread starter	Title	Forum	Replies	Date
	Release Asuswrt-Merlin 3004.388.8_4 is now available	Asuswrt-Merlin	72	Sunday at 3:41 PM
	Release Asuswrt-Merlin 3006.102.2 is now available for Wifi 7 devices	Asuswrt-Merlin	62	Nov 3, 2024
B	Unable to establish VPN connection to my PiVPN (ovpn) from my Asus RT-AC86U running Asuswrt-Merlin 386.14	Asuswrt-Merlin	1	Oct 27, 2024
F	Several Questions Re:Asuswrt-Merlin Feature Implementation	Asuswrt-Merlin	2	Oct 16, 2024
	How to enable port randomization in Asuswrt-Merlin?	Asuswrt-Merlin	4	Oct 12, 2024
	Beta Asuswrt-Merlin 3006.102.2 Beta is now available for Wifi 7 devices	Asuswrt-Merlin	70	Oct 12, 2024
J	Does Asuswrt-Merlin support AiMesh over Wifi?	Asuswrt-Merlin	4	Oct 5, 2024
	Printing from Guest Network (ASUSWRT-Merlin 3004.388.8_2)	Asuswrt-Merlin	5	Oct 4, 2024
	Setting dnsmasq on Asuswrt-Merlin	Asuswrt-Merlin	8	Sep 18, 2024
	fwupdate.asuswrt-merlin.net - diversion.ch Down?	Asuswrt-Merlin	7	Aug 26, 2024

Asuswrt-Merlin 380.59 is now available

Part of the Furniture

Asuswrt-Merlin dev

Regular Contributor

Asuswrt-Merlin dev

Occasional Visitor

Regular Contributor

Regular Contributor

New Around Here

Occasional Visitor

New Around Here

Asuswrt-Merlin dev

Regular Contributor

New Around Here

Asuswrt-Merlin dev

Occasional Visitor

Asuswrt-Merlin dev

Occasional Visitor

Asuswrt-Merlin dev

Very Senior Member

Very Senior Member

Similar threads

Similar threads

Support SNBForums w/ Amazon

Sign Up For SNBForums Daily Digest